User Account

All Pages

SPD3303 Combustion and Heat Transfer of Premixed Assignment

Assignment Help Mechanical Engineering
Reference no: EM132398995

SPD3303 - Combustion and Heat Transfer of Premixed LPG/Air Flame - The Hong Kong Polytechnic University

Objective:

To explore the combustion and heat transfer characteristics of premixed LPG/Air flame by:

I. Investigate the "flash-back" and "up-lift" characteristics of the premixed LPG/Air open flame.

II. Investigate the heating efficiency of the premixed LPG/Air impinging flame operating at different Reynolds Numbers.

Discussions and Conclusion:

The following questions may be helpful to make your discussions and draw your conclusion:

Question 1. Why "Flash-back" is obtained at too low Reynolds Number whereas "Up-lift" is achieved at too high Reynolds Number in Experiment (I)? Explain the mechanisms behind these phenomena.

Question 2. What have you observed when "Flash-back" or "Up-lift" is occurring in Experiment (I)? Describe the flame shape, color and stability.

Question 3. Why the heating efficiency is always less than 100% and varying with Reynolds Number of the LPG/Air mixture jet in Experiment (II)?

Question 4. Explain and estimate (in percentage) the sources of "experimental errors" in Experiment (II).

Question 5. What will happen to the experimental results if the fuel supply is double in Experiment (II)?

Attachment:- Engineering Thermodynamics.rar

Reference no: EM132398995

Questions Cloud

What two criteria must be balanced in successful erm model : What other strategic processes are closely tied to ERM? What two criteria must be balanced in a successful ERM model?
Discuss how you would handle the situation : You are a health information manager in a financially troubled acute care hospital responsible for coding functions. The hospital's administration has retained.
Traditional lines of vehicles with all electric models : Suppose General Motors wants to replace one of their traditional lines of vehicles with all electric models.
Describes kinds of populations that measure has been used : Perform some internet searches to see if you can find the paper that first introduced the measure and some articles that use the measure.
SPD3303 Combustion and Heat Transfer of Premixed Assignment : SPD3303 Combustion and Heat Transfer of Premixed LPG/Air Flame Assignment Help and Solution, The Hong Kong Polytechnic University - Assessment Writing Service
Discuss how social workers can implement policies : Post your thoughts on whether social workers might try to undermine the implementation of specific policies. What ethical issues might they confront?
What is the largest number that can be generated : What is the largest number that can be generated by algorithm
Practice use of dictionaries and file parsing with python : The purpose of this lab is to practice the use of dictionaries and file parsing with Python. Dictionaries are very useful tools when processing large data files
Analyze the data and relate them to housing for both : Discuss Challenges or Opportunities in this analysis section and relate them to housing for both indicators wages and unemployment

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Nickel has a fcc crystal structure and 0125 nm atomic

nickel has a fcc crystal structure and 0.125 nm atomic radius. draw two nearest parallel 110 planes in a fcc crystal

  What are the assumptions you made for the estimation

Describe a possible method to estimate the activation energy of densification during liquid phase sintering.

  Derive an expression for the required mass m of the block

The uniform rod BC has cross-sectional area A and is made of α mild steel that can be assumed to be elastoplastic with a modulus of elasticity E and a yield strength σY.

  A two dimensional velocity field is described by the

a two dimensional velocity field is described by the equation given below with a - 3 ms and b 12 ms. determine the

  Find the high- and low-temperature behavior of µ

Consider the same two-dimensional, ideal Fermi gas that you dealt with in the previous assignment. You will need the result of that assignment to do this one.

  A rigid 10 m3 tank contains water initially at 120degc with

a rigid 1.0 m3 tank contains water initially at 120degc with 50 liquid and 50 vapor by volume. a pressure-relief valve

  Compute the amplitude of vibration of the compressor

Select a suitable mounting and specify the design details by considering the static deflection of the compressor, the transmission ratio, and the amplitude of vibration of the compressor.

  Determine the shear strain

How is the specimen going to deform in the transverse direction (a, b, or c) for a material of the following properties? Prove your answer by numerical computation.

  Determine the magnitude of support reactions at a and c

SOLUTION OF the homogeneous 18kg(180N) pulley is attached to the bar ABC with a pin at B. the mass of the bar is negligible.the cable running over the pulley carries a tension of 600N.Determine the magnitude of support reactions at A and C

  For water at room temperature

For flow of viscous fluids through a 5 cm diameter pipe, for what flow rate in m3/h would we expect transition to turbulence?

  Which contract should the young genius choose

Assume the genius uses a MARR of 9%. Which contract should the young genius choose? Use a present worth comparison.

  Derive the equation for pure bonding of beam

Question - Derive the equation for pure bonding of beam (simply)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd