Spacing of the bands be near the bottom of the vat

Assignment Help Mechanical Engineering
Reference no: EM13704667

A cylindrical wooden storage vat has a 20 ft outside diameter. It is filled with 24 feet of brine with a specific gravity of 1.06. The wooden staves making up the vat are bound by flat steel bands evenly spaced vertically around the tank. Each band is 2-inches wide and ¼-inch thick. The allowable stress in each band is 16,000 psi. What should the spacing of the bands be near the bottom of the vat? Neglect any initial stress that is applied to the bands.

Hint: Think of how we did the derivation for a cylindrical pressure vessel.

Reference no: EM13704667

Questions Cloud

Explain the difference between phase change via evaporation : Research and explain the difference between phase change via evaporation and phase change via boiling. Name one device or consumer product that uses each of these phase change mechanisms. Cite your source(s)
Metal alloy has body centered cubic crystal structure : A certain metal alloy has body centered cubic crystal structure; it has an average atomic weight of 71.2 amu; and the metal has an average atomic radius of 0.131 nm. Determine the theoretical density of this metal in grams per cubic centimetre.
Net rate at which radiation is exchanged : A body whose surface area is 0.5 m2, emissivity is 0.8, and temperature is 150C is placed in a large evacuation chamber whose walls are at 25C. What is the rate at which radiation is emitted by the surface, in W? What is the net rate at which radiati..
Calculate in kpa and in atm : Fish swimming above a dam may be up to 260 feet beneath the surface of the lake. What ambient pressure change would a fish experience if it was pulled up to a boat? Calculate in kPa and in atm.
Spacing of the bands be near the bottom of the vat : A cylindrical wooden storage vat has a 20 ft outside diameter. It is filled with 24 feet of brine with a specific gravity of 1.06. The wooden staves making up the vat are bound by flat steel bands evenly spaced vertically around the tank. Each band i..
Amount of heat transfer through the glass : The inner and outer surfaces of a 5 mm window glass are maintained at 10°C and 3°C. What is the amount of heat transfer through the glass in 5 hrs?
Saturated moist air and condensate exit in separate streams : Air at 35 C, 1 atm, and 50% relative humidity enters a dehumidifier operating at steady state. Saturated moist air and condensate exit in separate streams, each at 15 C. Neglecting kinetic and potential energy effects,
Engine cover that is made with two layers of metal plates : Consider an engine cover that is made with two layers of metal plates. The inner layer is stainless steel (k1 = 14 W/m*k) with a thickness of 10 mm, and the outer layer is aluminum (k2 = 237 W/m*K) with a thickness of 5 mm. Both metal plates have a s..
Find the altitude of the balloon when it is dropped : A sandbag is dropped from a balloon which is ascending vertically at a constant speed of 6m/s. If the bag is released with the same upward velocity of 6m/s when t=0s and hits the ground when t=8s, neglecting air resistance,

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd