User Account

All Pages

Small part of the gauge section

Assignment Help Mechanical Engineering
Reference no: EM13887037

A tensile bar was machined so that most of the gauge section had a diameter of 0.500 cm. One small part of the gauge section had a diameter 1% smaller (0.495 cm). Assume power-law hardening with n = 0.17. The bar was pulled until necking occurred.

A. Calculate the uniform elongation (%) away from the neck.

B. Compare this with the uniform elongation that would have been found if there had been no initial reduced section.

Reference no: EM13887037

Questions Cloud

What factors would cause you to choose reperformance : You could test by either inspecting documentation of the reconciliation or by reperforming the reconciliation. What factors would cause you to choose reperformance instead of inspection of documentation?
Find the capacitance of the small capacitor : A capacitor of capacitance Co is charged to a potential Vo and then isolated. A small capacitor C is then charged from Co, discharged & charged again, the process being repeated n times. The potential of the large capacitor has now fallen to V. Fin..
How did theoretical teachings about race actually work : One strand you might want to keep an eye on is the relationship between theory and practice... in other words, how did theoretical teachings about race actually work out in real life
What level of quality and reliability-mean time between fail : What level of quality and reliability-mean time between failure (MTBF)-did you build into your products?
Small part of the gauge section : A tensile bar was machined so that most of the gauge section had a diameter of 0.500 cm. One small part of the gauge section had a diameter 1% smaller (0.495 cm). Assume power-law hardening with n = 0.17. The bar was pulled until necking occurred.
Why analysis of companys control environment is important : Explain why an analysis of the company's control environment is important to planning the integrated audit. The company claims that it has a strong control environment, including a culture of high integrity and ethics.
Write paper about jesus is both humanity and divinity : Write paper about Jesus Is Both Humanity And Divinity
Calculate the diameter away from the reduced section : Suppose that an investigator had not known that the bar initially had a reduced section and had assumed that the bar had a uniform initial diameter of 1.00 cm. Suppose that she measured the diameter away from the neck and had used that to calculat..
Definition of community health education theory : Definition of community health education theory. Then explain how community health education theory is different from other types of theories used in public health

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the magnitudes of fa and fb

The total force Fa + Fb exerted on the shelter is in the direction parallel to the line L and it's magnitude is 400 lb. Graphically determine the magnitudes of Fa and Fb.

  Piston-cylinder device with set of stops initially

A piston-cylinder device with a set of stops initially contains 0.6 kg of steam at 1.0 MPa and 400 C. The location of the stops corresponds to 40 percent of the initial volume. Now the steam is cooled. Determine the compression work if the final stat..

  Evaluated at the mean temperature in the slab

Prove that if k varies linearly with T in a slab, and if heat transfer is one-dimensional and steady, then q may be evaluated precisely using k evaluated at the mean temperature in the slab.

  What is the minimum volume of the balloon

A helium balloon lifts a basket and cargo of total weight 2000 N under standard conditions, in which the density of air is 1.29 kg/m3 and the density of helium is 0.178 kg/m3. What is the minimum volume of the balloon?

  Cld water cp 418 kjkgc leading to a shower enters a

cold water cp 4.18 kjkgc leading to a shower enters a well-insulated thin walled double-pipe counter-flow heat

  A computer cpu chip operates at steady state with d-c

a computer cpu chip operates at steady state with d-c electrical input of 4.5 amps at 9 volts. to prevent the chip from

  Determine the mechanical efficiency of the pump

An electric motor drives a pump, which moves a liquid fluorocarbon from a pipe with an inlet diameter of 13[cm] into a pipe with an outlet diameter of [8cm] at a rate of 0.15[m3/s]. The motor uses 200[kW] of electric power. The specific volume of the..

  Kinematic viscosity

Kinematic viscosity (select all that apply)

  Calculate the cross-sectional area of test rod with diameter

A load test on a 8-mm diameter by 375-mm long aluminium alloy rod found that a tension load of 4800N caused an elastic elongation of 0.52-mm in the rod. Using this result, determine the elastic elongation that would be expected for a 23-mm diameter r..

  Determine a the temperature of the air at the compressor

n air compressor operates at steady state with air entering at p1 1 bar t1 17 c and exiting at p2 5 bar. the air

  The convective heat transfer coefficient of the outside of

a spherical tank aisi 302 stainless steel has an outside diameter of 40cm and a wall thickness of 2cm. it contains

  Calculate the factor of safety the designer must have used

a small 6-mm diameter pin was designed using astm no. 40 cast iron to withstand an axial compressive load of 3.5kn

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd