User Account

All Pages

Slip range of induction motors

Assignment Help Mechanical Engineering
Reference no: EM13882305

Industrial plant consists of 4-motors and transformer. Two induction motors and two synchronous motors are installed with the following data:

The slip range of induction motors is between: s = 0.03-0.05

The induction motor at rated load power factor is between PF = 0.75-0.85 lagging. The induction motor rated sizes are available of 100, 150, 200, & 250 hp.

The efficiency of the induction motors is between 80%-90%

The synchronous motor rated sizes are available of 100, 150, 200, &250 kW.

The synchronous motor at rated load power factor is between PF = 0.80 lagging-0.80 leading. The efficiency of the synchronous motors is between 85%-92%

The motor poles are available of 2 or 4. The voltage source is VLL = 480V, 60Hz.

The total load torque of the plant is 2900 N.m.

The total power factor, PF, at the secondary side of the transformer is 1 ≥ PF ≥ 0.95 lagging.

1. Design the motor specification such as size, pole numbers, slip, efficiency, and PF based on the data available above. (note: Motors from each type cannot be the same rating)

2. Select proper transformer which can handle the total load taking to consideration 70% of load factor plus losses.

3. Show all your calculations in detail (power in all forms, currents, speeds, voltages, etc)

704_Design the motor specification.jpg

Reference no: EM13882305

Questions Cloud

Compare the three distributions and write up your conclusion : Approximate the distribution of the F-statistics for the three error distributions using the LINEST function to obtain the Whole Model F- statistic and the MCSim Add-in. Compare the three distributions and write up your conclusions.
Algebraically solve for phytolifes formula and its unit cost : Write up the standard linear program for PhytoLife. Graph and show PhytoLife's feasible set and a cost line. Using graphical techniques show the most attractive point. Algebraically solve for PhytoLife's formula and its unit costs.
Basic competitive advantage over u s commercial banks : Identify several large foreign institutions that are major lenders in the United States. Do any have a basic competitive advantage over U. S. commercial banks? Explain.
The p-value calculator add-in may prove helpful : est the following null hypothesis:Null Hypothesis: β1 = β2. Alternative Hypothesis: β1 /= β2.Use both the F- and t-statistic procedures and show that they produce equivalent results. The P-value Calculator Add-In may prove helpful.
Slip range of induction motors : Industrial plant consists of 4-motors and transformer. Two induction motors and two synchronous motors are installed with the following data: The slip range of induction motors is between: s = 0.03-0.05
Why did the u s banking system develop so differently : The U. S. system of banking historically led to many more banks that were smaller in size and operated with few branches. Why did the U. S. banking system develop so differently from that of other countries? What factors have brought about a change i..
Is the organization''s strategy producing satisfactory result : Is the organization's strategy producing satisfactory results?
Analyze the role this director took during the emergency : Select one (1) FEMA director whom you believe performed admirably during a major U.S. emergency or crisis. Next, analyze the role this director took during the emergency or crisis. Provide a rationale for your response
Explain multiple aspects of the managerial planning process : Explain the multiple aspects of the managerial planning process

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The fraction of steam extracted for feed water heating

Consider an ideal Rankine cycle with a single open feed water heater. The boiler pressure is 800 psia, and the condenser pressure is 2 psia. Steam is extracted from the turbine to heat the feed water at 90 psia. Steam enters the turbine at 1000F.

  Determine the astm grain size number if 25 grains per

1 for an astm grain size of 8 approximately how many grains would there be per square centimeter a at a magnification

  What is the flow rate of water when the gauges show a

a vertical pipe conveying water tapers from 50 mm in diameter at the top to 25 mm in diameter at the bottom in a length

  For a metal that has a yield strength of 401 mpa and a

for a metal that has a yield strength of 401 mpa and a plane strain fracture toughness kic of 21 mpa m12 compute the

  An electrical power transformer of diameter 250 mm and

an electrical power transformer of diameter 250 mm and height 600 mm dissipates 1200 w. it is desired to maintain its

  Determine the design thrust for a throat area

A rocket nozzle has a chamber pressure of 20 Bar (2 MPa) and a chamber temperature of 2750 K. The rocket is designed to operate isentropically at 12,500 m altitude. Note that the pressure at 12,500 m can be estimated using this equation P/P0 = exp [-..

  A presser relief valve has a pressure setting of 1500 psi

1 a presser relief valve has a pressure setting of 1500 psi. compute the horsepower loss across the valve if it returns

  What is the stagnation temperature at the outlet

The following information is known about the steady flow of methane through a horizontal insulated duct: Determine the outlet velocity. What is the stagnation temperature at the outlet?

  A supply pallet is dropped from an airplane

A supply pallet is dropped from an airplane that is climbing at 30 degrees with an indicated air speed of 600ft/s while traveling at an altitude of 12,000 ft. Determine how long it takes for the pallet to reach the ground from it's release point.

  A square 3m x 3m gate is located in the 45 sloping side of

a square 3m x 3m gate is located in the 45 sloping side of a dam. some measurements indicate that the resultant force

  Determine the natural frequencies and mode shapes

A two-story building frame is modeled as shown in Fig. The girders are assumed to be rigid, and the columns have flexural rigidities El1 and El2, with negligible masses. The stiff¬ness of each column can be computed as

  A very long cylinder diameter 1mm is placed perpendicular

a very long cylinder diameter 1mm is placed perpendicular to a steady airstream whose velocity is 10 msec. the cylinder

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd