Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
use the Timer_A device to generate the pulse-width modulated (PWM) signals. Assume that Timer_A is configured to operate in the UP mode, and the input clock has a frequency of 1 MHz. The TACCR0 is set to 999. Channel 1 and channel 2 are configured to generate output signals OUT1 and OUT2, with TACCR1 = 745, and TACCR2 = 499, respectively. And the output mode is set to Reset/Set. Sketch two periods of the output signals OUT1 and OUT2 (with proper labeling of the time axis).
A DSSS-CDMA signal has a chip sequence that is 10,000 chips in length. The sequence repeats every millisecond. What is the chip rate?
An amplifier has a power gain of 3dB and an input signal power P(In) = 100mW. What is the output power level A tank circuit coil is operating at a resonance frequency f(res) = 20 MHZ; The circuit must operate with a bandwith of 200 KHZ.
A radio receiver has antenna noise temperature of 3000 K and equivalent noise temperature of 7000 K for its feeder and amplifier cascade. It requires Eb/No = 15 dB to provide Probability of error of 10^-15 (using BPSK).
Consider a signal x(t) = 10 cos(2pi*fct + 4 cos 2pi*fmt). Assume frequency modulation. The message frequency fm = 2:3 kHz. Calculate the modulation index and find the bandwidth when.
The tray heats up according to ut = c2?u + h(x, y) where h(x, y) = 5(1 - sin(8πy)) and c2 = 10-4. Assume that u = 200 along each edge. Find the steady state temperature distribution of the tray.
design op amp circuit to produce output vout which is related to inputs v1, v2 and v3 by expression vout= -(3v1+5v2+8v3). assume max permitted resistor value= 200k.
The total admittance for the following circuit is Hint: YT = G + j[Bc - BL] Siemens; G = 1/R Siemens; Bc = wC Siemens and BL = 1/[wL] Siemens Data: Vin AC = 10 sin 1250t, R = 100, C = 4UF, L = 80 mH
Improve the controller designed in part by introducing a mechanism for the disturbance compensation at the plant input. Illustrate advantage of the improved controller by applying the fast varying piecewise constant reference input vector and sinu..
what is the magnitude and direction of the current flowing through the cross section?
Given the following: i) The column vectors: X1=[2 4 6]'; X2=[4 5 7]'; X3=[7 8 3]' % Note the above are column vectors (% In Matlab, ' means Transpose). ii) The matrix: A=[X1 X2 X3]. 1)B=A'; % In Matlab, ' means Transpose. This defines B.
1.explain what is the instantaneous values of AC AND phase shift angle are. Explain what the effective and average values of AC are. How are they related with amplitude. 2.Draw a calculated conductivities triangle for the circuit with a parallel co..
Suppose that the sequence 110010011 is used as a synchronization sequence preamble to a data packet. Propose a method that can be used to allow the channel to distinguish the synchronization sequence from an identical data sequence within the pack..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd