Sketch the ttt diagram for a typical high hardenability

Assignment Help Mechanical Engineering
Reference no: EM13634254

Sketch the TTT diagram for a typical high hardenability FeFe3C alloy with addition elements such as Ni, Mn, N, etc. in comparison to a binary FeFe3C alloy. Indicate the types of constituents of the steel expected to form on your diagram. Draw and label their typical microstructural features of all the possible micro-constituents of the steel.

Reference no: EM13634254

Questions Cloud

A person is standing on the roof of a tall building she : a person is standing on the roof of a tall building. she throws a ball from the top of the building in such a way that
The computer-science aptitude scorenbspx and the : the computer-science aptitude scorenbspx and the achievement scorenbspynbspmeasured by a comprehensive final were
A person exerts a force of 28n on the end of a door 84cm : a person exerts a force of 28n on the end of a door 84cm wide. what is the magnitude of the torque if the force is
Let a b and c be independent random variables uniformly : let a b and c be independent random variables uniformly distributed over 04 02 and 03 respectively. what is the
Sketch the ttt diagram for a typical high hardenability : sketch the ttt diagram for a typical high hardenability fefe3c alloy with addition elements such as ni mn n etc. in
A gasmixture contains 128 g n2 and 085 g o2 in a155 l : 1. calculate the root square mean velocity of cl2 at 25 ordmc.2. an unknowngas effuses at a rate that is 0.462 times
Gve the state temperature pressure quality if applicable : design a rankin cycle to analyze. the only restrictions are that water must enter the turbine as a superheated vapor
The kid twirls it just fast enough to keep it moving in a : a kid plays with a yo-yo of mass 125 g and twirls it in a vertical circle. the lneght of the string is 90.0 cm. the kid
For the funtion fx6x2 make a table of slopes of secant : for the funtion fx6x2 make a table of slopes of secant lines and make a conjecture about the slope of the tangent line

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Air is blowing out of a fan with exit diameter d 05 m

air is blowing out of a fan with exit diameter d 0.5 m with uniform velocity v 100 ms static pressure p 100000 pa and

  Carbon monoxide at 77f 1 atm enters and insulated reactor

carbon monoxide at 77f 1 atm enters and insulated reactor operating at steady state and burns with air entering at 77 f

  Each molecule can be viewed as a cylinder of initial length

molecules that are of density row180 kgm3 and spe- cific heat cp 3000 jkg k have an initial relaxed length of l2nm.

  Determine the flow capacity in lmin of the fan that needs

the minimum fresh air requirement of a residential building is specified to be 0.35 air change per hour ashrae standard

  Paint plant air house

Electricity might be used to run the fan to draw air through the system, and also to run a chiller - What is a typical COP for a commercial chiller?

  If the density of air is 12 kgm3 at the inlet and 105 kgm3

if the density of air is 1.2 kgm3 at the inlet and 1.05 kgm3 at the exit determine the percent increase in the velocity

  At a surface cutting speed of 190 mmin the productive tool

at a surface cutting speed of 190 mmin the productive tool life was 60 minutes. at a surface cutting speed of 225 mmin

  If a convection coefficient of 500 wm2middotk is maintained

as part of a heat treatment process cylindrical 304 stainless steel rods of 100-mm diameter are cooled from an initial

  The roller-coaster track shown is contained in a vertical

the roller-coaster track shown is contained in a vertical plane. the portion of track between a and b is straight and

  The steam expands adiabatically until its final pressure

a piston-cylinder assembly initially contains 0.15 m3 of steam at 20 bar and 320oc. the steam expands adiabatically

  As per the linked question how do you determine the

as per the linked question how do you determine the location of the resultant? why is located 23 deep and how do you

  At what rpm should the model be run what is the required

a 20 mw radial flow hydraulic turbine is to be designed with a head of 70 m and a speed of 90 rpm. a geometrically

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd