Sketch the t vs s cyclediagram for this ideal rankine power

Assignment Help Mechanical Engineering
Reference no: EM13633876

A non-ideal regenerative Rankine cycle for a power plant (shown below), where there is no heat loss or pressure drops in the piping, the turbine and pumps are "not" isentropic (q-out(turbine)=0.09 q-in(boiler), q-out(I)=0.02 q-in(boiler), & q-out(II)=0.03 q-in(boiler)), the heat loss in open feedwater heater (FWH) can be neglected, there are no pressure drops in the boiler, condenser, and FWH, and the steam leaves the condenser and FWH as saturated liquid.

a)sketch the T vs. s cycle/diagram for this ideal Rankine power plant (including the T vs. s bell-curve for water/steam and the exact values of P & v at each stage).

b)sketch the P vs. v cycle/diagram for this ideal Rankine power plant (including the P vs. v bell-curve for water/steam and the exact values of P & v at each stage).

c)what is Mass flow rate at stages 6 & 7?

d)how much heat input (to the boiler) is needed in 5 seconds?

e)what is the net rate of work output

state1: sat-liquid at 10kPa out of condeser into Pump1

state 2 sat liquid at 1.2Mpa out of Pump 1 into Open FWH

state 3: sat-liquid at 1.2MPa out of Open FWH into Pump 2

state 4: sat-liquid 15Mpa out of Pump 2 into boiler

state 5: Mass flow rate of 15kg/s, gas at 15MPa at 600 degrees Celsius out of Boiler into Turbine

state 6: Gas at 1.2MPa out of Turbine into Open FWH

state 7: gas at 10kPa out of Turbine into Condenser

at Pump2 you have q-out(II)

at Boiler you have q-in(boiler)

at Turbine you have q-out(turbine)

at Condenser you have q-out

at Pump 1 you have q-out(I)

Reference no: EM13633876

Questions Cloud

The mass of the rod is m and the magnitude of the impulse : a uniform rod is resting on a frictionless table when it is suddenly struck at one end by a sharp horizontal blow in a
What happens to therate if the concentration of potassium : when ethyl bromide is added to potassium t-butoxide the product is ethyl t-butyl ether.a what happens to the rate if
If instead the gold is drawn out into a cylindrical fiber : gold which has a density of 19.32 gcm3 is the most ductile metal and can be pressed into a thin leaf or drawn out into
A system consisting of 575 g of liquid water at 298k is : a system consisting of 57.5 g of liquid water at 298k is heated using an immersion heater at a constant pressure of1.00
Sketch the t vs s cyclediagram for this ideal rankine power : a non-ideal regenerative rankine cycle for a power plant shown below where there is no heat loss or pressure drops in
A 360g block hangs from a spring with k519 nm at t0s the : a 360g block hangs from a spring with k5.19 nm. at t0s the block is 18.4 cm below the equilibrium position and moving
How many beta particles are emitted in 180 s by a : cobalt-60 undergoes beta decay has a half life of 5.26 years.a how many beta particles are emitted in 180 s by a
A laser emitting at 6328nm illuminates a double slit a : a laser emitting at 632.8nm illuminates a double slit. a screen is positioned 2.00 m from the slits. interference
The thermal energy that is used to heat the water is being : water enters a steam generator as compressed liquid at 100 c 6mpa and exits as superheated vapor at 500 c 6mpa constant

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd