Sketch the p vs v cyclediagram for this ideal rankine power

Assignment Help Mechanical Engineering
Reference no: EM13633408

An the ideal regenerative Rankine cycle for a power plant (shown below), where there is no heat loss or pressure drops in the piping, the turbine and pumps are isentropic, the heat loss in open feedwater heater (FWH) can be neglected, there are no pressure drops in the boiler, condenser, and FWH, and the steam leaves the condenser and FWH as saturated liquid.

a)sketch the T vs. s cycle/diagram for this ideal Rankine power plant (including the T vs. s bell-curve for water/steam and the exact values of P & v at each stage).

b)sketch the P vs. v cycle/diagram for this ideal Rankine power plant (including the P vs. v bell-curve for water/steam and the exact values of P & v at each stage).

c)what is Mass flow rate at stages 6 & 7?

d)how much heat input (to the boiler) is needed in 10 seconds?

e)what is the net rate of work output?

state1: sat-liquid at 10kPa out of condeser into Pump1

state 2 sat liquid at 1.2Mpa out of Pump 1 into Open FWH

state 3: sat-liquid at 1.2MPa out of Open FWH into Pump 2

state 4: sat-liquid 15Mpa out of Pump 2 into boiler

state 5: Mass flow rate of 15kg/s, gas at 15MPa at 600 degrees Celsius out of Boiler into Turbine

state 6: Gas at 1.2MPa out of Turbine into Open FWH

state 7: gas at 10kPa out of Turbine into Condenser

Reference no: EM13633408

Questions Cloud

A proton is located at the origin and a second proton is : a proton is located at the origin and a second proton is located on the x-axis at x 5.38 fm 1 fm 10-15 m.a calculate
How exactly do you name a pyrrole because ive been : how exactly do you name a pyrrole because ive been attempting ahomework assignment and one of the structures is a
A student measures the melting point of benzil and reports : a student measures the melting point of benzil and reports themelting point in the lab notebook as 95c. explain what
A ski gondola is connected to the top of a hill by a steel : a ski gondola is connected to the top of a hill by a steel cable of length 620 m and diameter 1.5 cm. as the gondola
Sketch the p vs v cyclediagram for this ideal rankine power : an the ideal regenerative rankine cycle for a power plant shown below where there is no heat loss or pressure drops in
Each private locker in the gym building is labeled with : each private locker in the gym building is labeled with three upper-case alpha characters followed by two base 16
What is the probability that there are exactly 6 girls : what is the probability that there are exactly 6 girls among the first 10 and exactly 12 girls among the first 19
Solid lithium metal reacts with watergiving a solution of : solid lithium metal reacts with watergiving a solution of lithium hydroxide andreleasing hydrogen gas. write a balanced
Two positive point charges are held in place 060 m apart : two positive point charges are held in place 0.60 m apart. they are then moved so that their electric potential energy

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd