Sketch the cycle on a t-s diagram with respect to

Assignment Help Mechanical Engineering
Reference no: EM13612574

Water is the working fluid in an ideal vapor power cycle with reheat. Superheated vapor enters the first turbine stage at 8 MPa, 500oC and expands to 2 MPa. Then, it is reheated to 500oC before entering the second turbine stage, where it expands to the condenser pressure of 7.5 kPa. The mass flow rate of steam entering the first turbine stage is 2630 kg/h. Assume a source temperature of 1500 K and a sink temperature of 300 K. Take T0 = 300 K. Sketch the cycle on a T-s diagram with respect to saturation lines and determine (a) the rate of the heat input to the working fluid, in kW, (b) the rate of the heat rejected from the working fluid, in kW, (c) the net power output, in kW, (d) the thermal efficiency of the cycle, (e) the exergy destruction associated with each of the processes, in kW, and (f) the second law efficiency.

Reference no: EM13612574

Questions Cloud

Two pieceshaving equal mass fly off perpendicular to one : a vessel at rest explodes breaking into three pieces. two pieceshaving equal mass fly off perpendicular to one another
Role of management accounting review the roles of : role of management accounting review the roles of management accounting within a company. what is the most important
What would be the power output of an electric generating : approximately 10 6 kg of water drops 50m over niagara falls every second. how much potential energy is lost every
Cash flows information what information does the cash flow : cash flows information what information does the cash flow statement provide that you cannot see in the other financial
Sketch the cycle on a t-s diagram with respect to : water is the working fluid in an ideal vapor power cycle with reheat. superheated vapor enters the first turbine stage
The speed of an automobile traveling due to east is : the speed of an automobile traveling due to east is uniformaly reduced from 75.0km to 45.7kmh in a distance of 88.5m.a
A hockey puck on a frozen pond with an initial speed of : a hockey puck on a frozen pond with an initial speed of 18.9 ms stops after sliding a distance of 240.3 m. calculate
Determine a the maximum temperature in the cycle the net : a four-cylinder four-stroke 2.8-liter compression-ignition engine operates on the ideal dual cycle with a compression
What is the mass of the spaceship and the acceleration due : a spaceship is heading toward a planet. while descending to the surface its rockets produce 25 kn of upward thrust and

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd