Single-stage ideal regenerative steam cycle

Assignment Help Mechanical Engineering
Reference no: EM13712172

A single-stage ideal regenerative steam cycle has a boiler pressure and temperature of 5000 kPa and 500 C, and a condensing pressure of 10 kPa. The extraction pressure is 500 kPa. If the regenerative heater is a closed heater with the condensate pumped into the line following the heater (TTD=7 C), find:

(i) the net work, in kJ/kg,

(ii) the work ratio

(iii) the thermal efficiency

Reference no: EM13712172

Questions Cloud

Find the stagnation temperature and pressure : Flowing in a convergent nozzle. At a particular location within the nozzle the pressure is 280kPa, the stream temperature is 345K, and the velocity is 150 m/s. If the cross-section area at this location is 9.29 x 10^3m^2,
What is the viscosity of the liquid : A liquid is draining from a cylindrical vessel through a tube in the bottom of the vessel. If the liquid has a specific gravity of .85 and drains out at a rate of 1 cm^3/s , what is the viscosity of the liquid?
What would be the power output of the prototype : It is required that a pump be designed for use in a chemical plant such that it delivers 0.8 m^3/s of benzene with a pressure increase of 320 kPa. What is the expected flow and pressure increase produced by a model one-sixth the size of the prototype..
Determine the mass rate of flow through the nozzle : Air flows isentropic ally through a convergent-divergent passage with inlet area 5.2 cm^2, minimum area 3.2cm^2 and exit area 3.87 cm^2. At the inlet the eir velocity is 100m/s, is 680 kPa, and temperature 345 K.
Single-stage ideal regenerative steam cycle : A single-stage ideal regenerative steam cycle has a boiler pressure and temperature of 5000 kPa and 500 C, and a condensing pressure of 10 kPa. The extraction pressure is 500 kPa.
What is the apparent gravity at the counterweight : Space stations don't need to be round to have artificial gravity. The tethered spacecraft in the diagram to the right represents an alternative design. Put the astronauts in a passenger capsule. (Put the "spam in a can" as they say.) Tether it to a h..
Oil has a specific gravity : Oil flows at a rate of 12gpm from a vented tank (pressure at point 1 is zero) through 1 inch inner diameter pipes and elbows, and through a pump and motor as shown. The pump adds HHPp= 3hp to and the motor extracts HHPm= 1hp from the fluid power.
Solar energy impinging on outer layer of earth’s atmosphere : Solar energy impinging on the outer layer of earth’s atmosphere (usually called “solar constant”) has been measured as 1367W/m^2. What is the solar constant on Mars
Classify the following vulnerabilities using the risos model : Classify the following vulnerabilities using the RISOS model. Assume that the classification is for the implementation level. Justify your answer.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd