Single-stage ammonia vapor-compression system

Assignment Help Mechanical Engineering
Reference no: EM13706683

In theoretical (ideal) single-stage ammonia vapor-compression system, liquid leaves the condenser at 250 psia and 104 °F. Evaporator pressure is 18.30 psia. Vapor leaves the evaporator at 0°F. The system produces 25 tons of refrigeration. Determine

a. The coefficient of performance

b. The piston displacement (compressor displacement) in ft3/min

Reference no: EM13706683

Questions Cloud

Use transformation matrices : For a part with matrices (0,0,0),(1,0,0),(0,2,0),(0,0,3), find the final shape after being scaled with factors(1,2,3) in x,y,z axis and then mirrored about z=0 plane. Use transformation matrices.
Change in length due to temperature : Calculate the change in length of the steel and aluminium due to the temperature change alone. Then, assuming that the load P is not applied, and the temperature increases from 60?F to 110?F, calculate the change in length of the steel and aluminium.
Analyze a basic set of requirements for a problem : Analyze a basic set of requirements for a problem - Compose basic C++ language programs
Long log floats with its axis horizontal : It is known that a long log floats with its axis horizontal. A very short log, however, floats with its axis vertical. Determine the maximum length of a cylindrical walnut log 30 cm in diameter that will cause it to float with its axis vertical.
Single-stage ammonia vapor-compression system : In theoretical (ideal) single-stage ammonia vapor-compression system, liquid leaves the condenser at 250 psia and 104 °F. Evaporator pressure is 18.30 psia. Vapor leaves the evaporator at 0°F. The system produces 25 tons of refrigeration.
Calculate the delta velocity required to change inclination : Calculate the delta velocity required to change the inclination of a circular orbit at 32,000 km altitude from a 28.5 degree inclination to an inclination of 45 degrees. Compute the propellant used if the satellite weighs 1200 lbs after the maneuver.
Assume sea level pressure : Moist air at 70 F dry bulb temperatures and 45 percent relative humidity is recalculated from a room and mixed with outdoor air at 97 F dry-bulb temperature and 83 F thermodynamic wet bulb temperatures. Determine the mixture state dry-bulb and wet-bu..
Determine the relative humidity : Air with a dry bulb temperature of 38°C and a dew point temperature of 20 °C is at a barometric pressure of 93.1 kPa. Without making use of the psychrometric chart for the given moist air determine the relative humidity
Velocity required in changing position of satellite in orbit : Calculate the change in velocity required in changing the position of a satellite in an orbit by 90 degrees. The initial and final orbit is circular around the Earth with a 15000 km radius. Calculate the delta velocity, semi-major axis and period for..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd