Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Objective is just to simulate the system without controller. At some values of wind speeds, I want to play with the duty cycle values of the converter and read its corresponding output power.
the impact of changing duty cycle on extracted output power at different wind speeds.
for example:
wind speed = 12 m/s
duty cycle = 0.1, 0.2, 0.3 ,.....,0.9 then, just measure the output power for each duty cycle value and that's it. then, change the wind speed and do the same and so on. How to simulate the system for the first time.
This is exactly the system I want to simulate using SIMULINK:
I don't have the values of the components parameters and how to relate the values of the components parameters to each other.
The average intensity of sunlight reaching the earth is 1390W/m2. A charge of 2.38 x 10-8 C is placed in the path of this electromagnetic wave. What is the magnitude of the maximum electric force that the charge experiences
The resistance of the filament of the bulb, measured with a standard multimeter, is 16.7 ohms. When the bulb is connected into the circuit and is operating at the rated values given above determine a) the resistance of the filament b) the efficien..
using the time independent one dimensional schrodinger equation find the expression of the allowed energy levels for
Design a unity gain first order lowpass digital filter with a 3dB point at Fc=100Hz using Bilinear Transformation. The sampling rate is 1kHz. A first order analog filter is given by Ha(s)=θc/(s+θc) (a) What is the 3-dB frequency of the above analog ..
Find the Laplace transform of the following: (i) f(t)= 45e^(-5(t-6)) (j) f(t)=2 sin(t-6) (k) f(t)="4.8" e^(-5t) cos?(400t -36o) (l) f(t)=8 d2x/dt2 + 5 dx/dt where (dx(0))/dt = 8 and x(0) = -4
The high-voltage windings are connected in Y with a solidly grounded neutral. Draw the per-unit zero-, positive-, and negative-sequence networks if the low-voltage wind- ings are connected: (a) in D with American standard phase shift
Consider a Si p-n junction with n-type doping concentration of 10^16 cm^-3. This junction is forward bias with V=0.8 V at 300 °K. Calculate the minority-carrier hole concentration at the edge of the space charge region.
Write the theoretical Power Spectral Density for a BPSK signal with shift angle of 180 degrees, carrier of 25 kHz and bit rate of about 1 kHz that has been spread by a PN sequence with a bit rate of about 100 kHz. State it or derive it.
Assume a buck converter contains a synchronous rectifier. Does it operate in the discontinous conduction mode at light load Why What does the inductor current waveform look like
Design a system that repeatedly computes and outputs the sum of all positive numbers within a 512 word register file A consisting of 32-bit signed numbers.
Design an FSM that realizes a three-bit Gray-code counter, which counts in the sequence 000, 001, 011, 010, 110, 111, 101, 100, 000
Then, solve each Problem using hand calculations. A three-phase, 765-kV, 60-Hz transposed line is composed of four ACSR 1,431,000, 45/7 Bobolink conductors per phase with flat horizontal spacing of 14 m. The conductors have a diameter of 3.625 cm ..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd