Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Required Number of Words: 3000
The attached JPEG file labeled "Analog channel", is the signal conditioning circuitry of the controller card of a tensometer being inserted in (IDE slot of the host PC (controlling the machine which is the tensometer). The input of the circuit is given through the header pin P7 on the top left corner of the circuit diagram and coming from the stain gage of the tensometer. The output (voltage) of the circuit is given as digital pattern out by the CS5503, on the far right side of the circuit. Pins 2 and 5 of P7 provide the reference voltage, and pins 3 and 4 provide the differential voltage of the strain gage.
The topic of the assignment is developing a detailed analysis and discussion about if the signal conditioning could all be handled by AD7710 chip. Could a single AD7710 chip handle all signal conditioning so that it directly connects to header pin P7, receiving analog input voltage, and directly giving the output? Or if AD7710 could not be used in this application, what is the reason? What are the restrictions of using AD7710? Completely explain. Your reasoning should refer to the functionality of the original circuit (which is the Analog channel) components. Do notice that merely explaining capabilities and incapability's of AD7710 without referring to the functionality of Analog channel components is not acceptable. You should relate the role of Analog channel components to the functionality of AD7710.Should be properly referenced. Notice that in-text referencing is a must; indicating the page numbers of the datasheets where information is sought from.
Attachment:- Analog channel.rar
A square wave has the following properties: Period(T)=5mS, Vmax= 3V, Vmin=-7V, Duty cycle=84%. Calculate the Vrms of this square wave.
What is Thyristor and SCR (Silicon Controlled Rectifier) and its Construction , and mention the Difference between Thyristors and Transistors .
Compare the parameters obtained to the tabulated values - The load on the line is 70 MW at 100% power factor. Use attached Tables A3 to A5 to determine.
Discuss why the primary of a power transformer would have excessive current if the secondary were short-circuited. Why would there be no voltage across the secondary if the primary is open. Explain how a transformer with a 1:1 turns ratio.
1. What parameter of the intelligence signal causes or determines the rate of carrier frequency deviation 2. If you are tuned to an FM station at a frequency of 100.1 MHz, show the bandwidth allocation for two adjacent stations.
register windows each have 6 input registers and 6 output registers. how many local registers are in each register
A DC power supply is adjusted to give a no load output voltage of 15 volts with the AC line voltage of 115 volts rms. A full load current of 1A is drawn into the circuit and the output voltage drops to 14.89 volts.
The quality control department at Alexander fasteners measured the length of 100 bolts randomly selected from a specified order.The mean length was found to be 9.75 cm, and the standard deviationwas 0.01 cm.
What happens to the program counter (PC) when a subroutine is called. What register is used to keep track of the return point. What happens to the register that keeps track of the return point if a subroutine calls another subroutine
A receive earth station has a line loss of 0.1 dB, followed byan amplifier with noise temperature 100 K and gain 50 dB, and areceiver with noise figure 30 dB. What is the equivalent noisetemperature [K] of this cascade of 2-port devices
a 741C is an op amp with Av= 100000 and a minimum CMRRdB= 70dB. what is the common- mode voltage gain. if a desired and common- model signal each has a value of 5 uV. what is the output voltage.
Design a circuit using an 8-to-1 multiplexer that functions as a 4bit odd parity generator. An odd parity generator outputs 1 if andonly if an even number of inputs are high.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd