Show the heating-humidification process on a sketch of the

Assignment Help Mechanical Engineering
Reference no: EM13628654

A solar collector is used to dry biomass in a storage bin. Outside air at 35o and 60% RH enters the collector and is heated to 90oF. The air saturates adiabatically (constant energy) as it moves through the biomass. Assume the energy required to heat the biomass is negligible and the air is saturated as it leaves the storage bin while answering the following:

a) Show the heating-humidification process on a sketch of the psychrometric chart by drawing lines showing the process. Indicate where the air is in the solar collector and where it is in the biomass.

b) How much energy (BTU) must be added to each pound of dry air?

c) How many pounds of water per pound dry air is added to the air as it moves thru biomass?

d) A fan forces air through the solar collector and grain mass at a rate of 500 cfm. How many gallons of moisture are removed from the biomass each day?

d) What are the final wet bulb and dry bulb temperatures of the air?

Reference no: EM13628654

Questions Cloud

The half-life of a radioactive substance has been defined : 1 explain why almost all naturally-occurring isotopes have a greater number of neutrons than protons.2 when two small
A study comparing the resting heart rate of four different : a study comparing the resting heart rate of four different types of elite athletes recruited 10 cyclists 10 triathletes
Explain why almost all naturally-occurring isotopes have a : 1 explain why almost all naturally-occurring isotopes have a greater number of neutrons than protons.2 when two small
If the chain has a weight of 3 lbft and the man weighs 150 : the man picks up a 52-ft chain and holds it just high enough so it is completely off the ground. the chain has points
Show the heating-humidification process on a sketch of the : a solar collector is used to dry biomass in a storage bin. outside air at 35o and 60 rh enters the collector and is
A wooden box item sits on a horizontal wooden board the : 1 . a wooden box item sits on a horizontal wooden board. the coefficient of static friction between the box and the
Explain why it takes less energy to ionize a hydrogen atom : 1 a hydrogen atom undergoes a transition from the n 12 state to the n 5 state. explain why it emits a photon during
The average weight loss was 167 lbs with a sample standard : six people suffering from weight problems are put on a year-long exercise regimen and their weights before and
A 45-g bullet is fired with a velocity of 600 ms into a : a 45-g bullet is fired with a velocity of 600 ms into a wooden block which rests against a solid vertical wall. knowing

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd