Show that the radial outlet velocity at the impeller tip is

Assignment Help Mechanical Engineering
Reference no: EM13639891

Consider a double-sided centrifugal compressor with the following design parameters:

Outlet diameter of impeller: 50 cm
Speed, N: 270 rev/s
Mass flow rate, m : 16.0 kg/s
Inlet stagnation temperature, T01: 288 K
Inlet stagnation pressure, p01: 1.01 bar
Isentropic eciency of impeller only,c : 0.9
Radial gap of vaneless space: 4.0 cm
Axial depth of vaneless space: 5.0 cm
Slip factor, σ: 0.9
Power input factor, : 1.04

Calculate the following:

1) The stagnation pressure, p02 and stagnation temperature, T02 at the outlet of the impeller, assuming no pre-whirl (i.e., Cw 1 = 0).

2) Show that the radial outlet velocity at the impeller tip is about 96 m/s and hence find the Mach number and air leaving angle at the impeller tip. Neglect the thickness of the impeller disk when calculating areas.

3) Assuming isentropic diffusion in vaneless space, find the correct angle of the leading edges of the diffuser vanes, and also find the Mach number at this radius.

Reference no: EM13639891

Questions Cloud

The heat of formation of kcls is -4367 kjmol and the heat : the heat of formation of kcls is -436.7 kjmol and the heat of formation of kclaq 1 m is -419.5 kjmol. determine the
Now a conductor is inserted into the capacitor the : an isolated capacitor with capacitance c 1 microf has a charge q 45 microc on its plates.a what is the energy stored
Assume that event a occurs with probability 04 and event b : 1. assume that event a occurs with probability 0.4 and event b occurs with probability 0.5. assume that a and b are
4 lbm mixture of 50 argon and 50 nitrogen by mole is in a : 4 lbm mixture of 50 argon and 50 nitrogen by mole is in a tank at 300 psi 320 r. determine the volume ot the tank using
Show that the radial outlet velocity at the impeller tip is : consider a double-sided centrifugal compressor with the following design parametersoutlet diameter of impeller 50
The vapor pressure of pure water at 500 degc is 925 mm hg : the vapor pressure of pure water at 50.0 degc is 92.5 mm hg. calculate the ideal partial pressure of water at this
Why is the probability of getting two red balls when : the applet below simulates sampling from an urn containing n balls. the total number of balls in the urn the number of
Aerosol cans carry clear warnings against incineration : aerosol cans carry clear warnings against incineration because of the high pressures that can develop upon heating.
Find the inverse cdf of given distributions using r let the : find the inverse cdf of given distributions using r1 logistic1022 pareto213 weibull234 gamma355 beta352 let the inverse

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd