Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Consider the two functions:
F(A,B,C,D)=Σ(0,2,3,4,6,7,10,11) and G(A,B,C,D)=Σ(0,4,8,9,10,11,12,13)
Consider that the functions are to be implemented as part of the same circuit. Show k-maps that reduce the total number of gates needed. How many gates are required?
A 25 MVA, three phase, 13.5kV, Y-connected, two pole, 60 Hz synchronous generator was tested by the open circuit test and short circuit test and tabulated in table 1. If the armature resistance is 0.24 ohms per phase
A 15hp (output power), 208V, three phase, six pole, y-connected induction motor has the following parameters: R1 = 0.1 ohm R'2= 0.1 ohm Xeq = 0.5 ohm A.) A fan type load is connected to the motor. The slip of the motor in this case is 2%.
Use the simulation timing diagram to compare the worse case time to do an operation with your ALU with the worst case using the 74LS381. State which operation takes the longest and list the time required for both ALU's.
How does this cost compare with the current cost of new coal figured generation at 3.5¢/kWh? Write a brief (400 words or less) argument on why Colorado should or should not shut down its coal power plants and replace them with wind farms?
An Ideal Low Pass Filter: The impulse response of an ideal low-pass filter is h(t) = sin(t)/t (or the sinc signal). (a) Given that the impulse response is the response of the system to an input x(t) = f(t)with zero initial conditions
A car with a projected frontal area of 1.8 m^2 is traveling at 136 KPH. If the drag coefficient of the car is 0.45 and the air density is 1.23 kg/m^3, find the total aerodynamic drag force on the car, and the power required to overcome this drag f..
Refer to the Wheatstone Bridge diagram. If R1=1ohm, R2=111ohm, Runknown= 1ohm, R3 is set at 1Kohm, and the battery is 9V:What is the current flowing through the galvanometerohm Use 60ohm for the internal galvanometer resistance in calculations.
A buffer amplifier with a gain of 1 V/V has an input resistance of 1M and an output resistance of 10 ohm. It is connected between a 1-V, 100-k ohm source and a 100-ohm load. What load voltage results and what are the corresponding voltage, current,..
A sequential circuit with three D-type flip-flops Y1Y2Y3, input X and output Z is defined with the following input/output functions: D 1 = X Y 3 + X Y 1 Y 3 D 2 = X ( Y 3 + Y 2 ) + X Y 2 Y 3 D 3 = X Y 3 + Y 2 Y 3 Z = Y3
Design a 2-bit counter that, when v = 1, counts in the repeating sequence: 0, 3, 1, 2, and when v = 0, counts in the reverse direction. (a) Construct a state diagram and state table. (b) Implement the counter using D flip-flops.
A two-resistor voltage divider consists of a 10 k and a 15 k ohm resistor, with the 10 k resistor connected to the voltage source and the 15 k resistor connected to ground. If the output voltage is 2.5 V across the 10 k resistor
Box 1 contains 5 red, 6 white, and 9 blue balls. Box 2 contains 7 red, 8 white, and 4 blue balls. A ball is withdrawn at random from Box 1 and placed in Box 2. Then, a ball is taken at random from Box 2.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd