Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The standard molar entropies of water ice, liquid and vapor are 37.99, 69.91, and 188.83 J K-1mol-1, respectively. On a single graph, show how the Gibbs energies of each of these phases vary with temperature between - 20 C and 150 C for a constant pressure of 80 kPa. You can start your computations at the triple point (pressure of 0.611 kPa and temperature of 0.01 C) where the molar Gibbs energy of all three phases are equal and can be assigned an arbitrary value of 1000 J mol-1. Use a molar volume of liquid water of 0.018 L mol.
During a snowstorm the fluoride feeder in North Bend runs out of feeder solution. The rapid mix tank is connected to a 5-km long distribution pipe. The flow rate into the rapid mix tank is 0.44m^3/sec, and the volume of the tank is 2.50 m^3.
Test reveal that a normal driver takes about 0.75s before he can react to a situation to avoid a collision. It takes about 3 seconds for a drunk driver to do the same. If such drivers are traveling on a straight road
The flowrate through an open channel with a slope of 2 % is calculated using Manning's equation at 100 cubic feet per second. If the slope of the channel is doubled to 4%
Assume a cross-sectional medial length of 32 in. (no stretching of the sheet due to bending). If the maximum shear stress must be limited to 19 ksi, determine the maximum torque that can be carried by the hollow section
A direct shear test is performed on a saturated specimen of loose sand. A normal stress equal to 100 kPa is applied and a maximum shear stress of 75 kPa is measured in the shear test. Determine the principal stresses and the orientation of these p..
A cylinder with a 6.0 in., diameter 12.0 in. height is put under a compresive load of 150 kips. The modulus of elasticity for this specimen is 8000 ksi and Poisson's ratio is 0.35. calculate the final length and the final diameter of this specuman..
a rectangular bar of length l has a slot in the middle half of its length. the bar has width b, thickness t, and modulus of elasticity E. the slot has a width b/4. the stress in the middle region is 24000 psi, the length is 30 in, andthe modulus o..
THe upper end of the spring is welded to the lunger and the lower end is welded to the base plate. If the plunger is lifted 1.5" above equilibrium and released from rest, calculate its velocity as it strikes A.
If the aircraft flies at 9000 m standard altitude, make a plot of drag (in N) versus speed (from stall to 240 m/s) and determine the optimum emise velocity (minimum drag per unit speed).
indicate the conditons by a sketchand determine the difference in the rate of grade at the intersection of each of the following paris of slops.
If the overall gear reduction ratio is 8 to 1, what is the maximum acceleration from rest (in ft/sec^2) for: a) the car with the base engine? b) car with the modified engine? Assume the car is on good dry pavement.
An irrigation channel is constructed of earth and is 8.1km long and has a capacity of 10 m^3/s for a flow depth of 2m. The cross section is trapezoidal with a bid width of 8 m and side slopes of 2 horizontal to 1 vertical.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd