Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Design constraints
Fig shows the reference schematic for the design assignment. The arrangement and connection points (also called "topology") in the schematic must not be altered. V1=-5 V and V2=5 V are the supply voltages and must not be changed. No parts may be added. Your task is to select the right resistor and transistors.
1. The resistors must be standard values (see Appendix).2. The transistors must be either BC548 (NPN) or BC558 (PNP) series (choose A, B, or C; see Appendix; I suggest picking one type in the first instance).
DC operating point
The following design targets must be met to within the said tolerance.
1. Collector current of Ic(Q3)=Ic(Q4)=1 mA (±10%).
2. Collector current of Ic(Q7)= 2 mA (+10%).
3. DC level of the output voltage V(vout) = 0V(±0.2V).
4. Use only a standard value resistor.
Attachment:- Design constraints.rar
Hello how much will it cost to solve this question? LTspice is useful to get the values, i will send the appendix for transistors value later.
To reduce the starting current, a three-phase squirrel-cage induction motor is started by reducing the line voltage to Vs/2. By what factor are the starting torque and the starting current reduced?
a change in the coil over a period of 4mSec causes total flux in the core to decrease at a constant rate by a total of 0.10 mWb. What voltage is induced in the 1000 turn coil by the change in flux.
Design a combinational circuit with four inputs and four outputs. The output generates the 2's complement of the input binary number.
Two metal plates with an area of 4 cm2 and separation distance of 0.01 cm are used to form a capacitance transducer. If the material between the two plates has a dielectric constant of 2.5 and the dielectric constant of free space is 8.85 pF/m
For radio channels the constellation size is often 4, for moderate signal to noise ratios. for such a constellation size in a 5 MHz channel using QAMP with no intersymbol interferance, what is highest bit rate ?
Suppose the circuit is designed for a nominal gain of 2.00 but the R1 and R2 suffer from a mismatch of 5% (i.e., R1 = (1 ±0:05) R2). What is the actual voltage gain?
Why is the cost of owning a "green" building often less than the cost of owning a conventionally constructed building?
The objective of this exercise is to design a microcomputer-based IEEE488 to RS422 simplex converter (Figure 14.23).
(A) A 6-H and 4-H coil are connected in series. What is thevalue of the total inductance (B) What is the value of thetotal inductance when the same two coils are connected inparallel
If JK flip flop has 1600hz frequency then what is the input frequency?
EET 3329C – Communication systems - valencia college - perform Fourier analysis for a square wave and to extract fundamental and harmonics using band-pass
Consider a causal continuous-time LTI system whose input x(t) and output y(t) are related by the following differential equation: dy(t)/dt + 4y(t) = x(t). Find the Fourier series representation of the output y(t) for each of the following inputs
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd