Saturated water at mean temperature 20 degc flows inside a

Assignment Help Mechanical Engineering
Reference no: EM13344103

Saturated water at mean temperature = 20 °C, flows inside a 25-mm-ID circular tube which is electrically heated to provide a constant heat flux over the entire length. The mass flow rate is 0.0295 kg/s. At a location 2.74 m downstream of the tube inlet, surface temperature is given to be 38 °C. Determine the total heat transfer rate for a 3.05 m - long tube. 

Reference no: EM13344103

Questions Cloud

A six-station automatic assembly line has an ideal cycle : a six-station automatic assembly line has an ideal cycle time of 12 sec. downtime occurs for two reasons. first
How much water would be needed to completely dissolve 178 : how much water would be needed to completely dissolve 1.78 of the gas at a pressure of 730 and a temperature of 27? a
It is dispersion less up is independent of frequency and 2 : q in addition to not dissipating power a lossless line has two important features i it is dispersion less up is
The half-life of tritium 31h is 123 years if 470 mg of : the half-life of tritium 31h is 12.3 years. if 47.0 mg of tritium is released from a nuclear power plant during the
Saturated water at mean temperature 20 degc flows inside a : saturated water at mean temperature 20 degc flows inside a 25-mm-idnbspcircular tube which is electrically heated to
Two mosfets are employed as current-bidirectional : two mosfets are employed as current-bidirectional two-quadrant switches in a bidirectional battery chargerdischarger
In step 5 of the experimental procedure 10 g of zinc is : in step 5 of the experimental procedure 1.0 g of zinc is added to the copperii sulfate solution to produce copper metal
What combustion products are produced when materials made : air monitoring provides the following contaminant concentrations at the approximate center of a fire scene in which
A 100 ml sample of 0200 m aqueous hydrochloric acid is : a 100. ml sample of 0.200 m aqueous hydrochloric acid is added to 100. ml of 0.200 m aqueous ammonia in a calorimeter

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the force of attraction

Calculate the force of attraction between a K+ cation and a O2- anion, the centers of which are separated by a distance of 1.5 nm.

  Determine the instantaneous center of rotation

determine (a) the instantaneous center of rotation of the double pulley (b) the velocity of th slider block (c) the number of inches of cord wrapped or unwrapped on each pulley per second.

  Find the desired radius and mass of the absorber

Find the desired radius and mass of the absorber if the absorber is to not exceed an angular deflection amplitude of 30 degrees when the engine is running at 750 rpm.

  At what location s will the combined moment of the weights

At what location S will the combined moment of the weights of the man and platform about point B be zero?

  What steel specification suitable for structural application

Find the stress in both members shown below and what steel specifications (types of steel) are suitable for structural applications?

  What are the tensions in cables ab and ac

Two tow trucks lift a 660 lb motorcycle out of a ravine following an accident. If the motorcycle is in equilibrium in the position shown, what are the tensions in cables AB and AC?

  Determine the expressions for the principal stresses

A circular shaft is subjected to a torque Ta and a bending moment Ma. Assuming that the diameter of the shaft is d, determine the expressions for the principal stresses and maximum shear stress in terms of Ma, Ta and d.

  Set up the negative feedback system

Using MATLAB Simulink, set up the negative feedback system of and find the value of the gain

  Calculate how many pounds of strawberries are needed

To make strawberry jam, crushed strawberries and sugar are mixed in a 45:55 mass ratio, and the mixture is heated to evaporate water until the residue contains one-third water by mass. Calculate how many pounds of strawberries are needed to make a..

  What can be said about the expected defect rate

Given that the nominal diameter (per print) is 15.00mm +/-0.10mm, what can be said about the expected defect rate?

  Level process control lab

Determination of the open-loop system

  What is the strain when the load is applied

What will be the length of the specimen after the load is removed? d) The specimen was reloaded until fracture. If the % reduction in area after fracture was 40%, what is the minimum diameter of the specimen at fracture?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd