User Account

All Pages

Sampled digitally at sampling frequencies

Assignment Help Mechanical Engineering
Reference no: EM131009318

1. (a) A sine wave at frequency f= 90 Hz is sampled digitally at sampling frequencies fs=200,160 and 50 Hz respectively. For each case, discuss whether there is aliasing. Also for each case, calculate the aliasing (perceived) frequency.(b) Using EXCEL (or Matlab or any other computer program) generate a sine wave at 90 Hz, DC offset =1.0 V, and amplitude = 2.2 V. Plot a smooth curve representing the real signal. Plot the time axis from 0 to 0.2 seconds, and the vertical axis from -2 to 4 V. On the same plot, plot the digitally acquired data (at 50 Hz sampling frequency) as symbols connected by straight line segments. Calculate the observed frequency from your plot and compare with the frequency calculated in part (a) and discuss briefly.

2. The signal-to-noise ratio SNR is defined as SNR=20log(Vsignal/Vnoise).(a) Calculate the signal-to-noise ratio SNR of an 80 Hz electrical signal with amplitude 2.00 V containing noise at 3600 Hz with amplitude 0.150 V.(b) In order to reduce the noise level the signal is filtered using a 2nd-order low-pass filter with a cutoff frequency of 100 Hz. Calculate the signal-to-noise ratio (SNR) with the filter and compare with part "a".Does the filter significantly improve the SNR?

Reference no: EM131009318

Questions Cloud

Overview of societal marketing practices of chosen company : An overview of the societal marketing practices of the chosen company and The type of promotions undertaken to support the programs
Create a new product that would appeal to your market : Choose the target market for your product, and describe your target market in detail. Create a new product that would appeal to your market. Develop at least one question for each characteristic of the target market
Consider the gas carburizing of a gea : Consider the gas carburizing of a gear of 1020 steel at 927oC. Calculate the carbon content at 0.5mm beneath the surface of the gear at 5hr carburizing time
The strategy for controlling the rotor speed of a variable : The strategy for controlling the rotor speed of a variable speed wind turbine is to aim at the relation shown in the figure below between the rotational speed of the generator and the generator power.
Sampled digitally at sampling frequencies : A sine wave at frequency f= 90 Hz is sampled digitally at sampling frequencies fs=200,160 and 50 Hz respectively. For each case, discuss whether there is aliasing. Also for each case, calculate the aliasing (perceived) frequency.(b) Using EXCEL (or M..
Data measure imports of goods and services : These data measure imports of goods and services into the United States, quarterly from 1981 through 2011 1n  = 124 quarters2. The data are given in billions of dollars, expressed at an annual rate. The data table includes a column named Quarter, wit..
Data measure imports of goods and services : These data measure imports of goods and services into the United States, quarterly from 1981 through 2011 1n  = 124 quarters2. The data are given in billions of dollars, expressed at an annual rate. The data table includes a column named Quarter, wit..
Calculate the carbon content at 0.5mm beneath : Consider the gas carburizing of a gear of 1020 steel at 927oC. Calculate the carbon content at 0.5mm beneath the surface of the gear at 5hr carburizing time. Assume the carbon content at the surface is 0.90% and that the steel has a nominal carbon co..
Problem regarding the compensation : These data measure hourly compensation in the US manufacturing sector from 1987 through 2011. The data are assembled by the Bureau of Labor Statistics from surveys. The value of the index was set to 100 in 2005, so the data indicate relative amoun..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the total rate of their heat transfer

Metal balls 10 mm in diameter are to be annealed by heating them to 827°C then allowing them to cool slowly in air at 27°C to the point where they are in thermal equilibrium with the air. 2000 balls are annealed in one hour’s time. What is the total..

  Determine the absolute pressure

A manometer is used to measure the air pressure in a tank. The fluid used has a specific gravity of 1.25, and the differential height between the two arms of the manometer is 28 in. If the local atmospheric pressure is 12.7 psia, determine the abs..

  A person is trying to fill a 100 gallon bucket by hand with

a person is trying to fill a 10.0 gallon bucket by hand with a dipper. one dipper of water is added each second and the

  Reasonable values of cylinder temperature

Design a single-cylinder atmospheric engine capable of lifting a mass of 1000 kg to a height of three meters. Assume reasonable values of cylinder temperature and pressure after combustion.

  The gas is known to have a density of 10 ppg at reservoir

a tilted gas sand encountered at 4500 ft is known to have a pore pressure of 2700 psig. a well is to be drilled near

  What is the angular acceleration of the disk for this value

when a disk rolls on a surface without slip the velocity of the point of contact of the disk with the surface is zero

  A car tire pressure is 22 bar at 25 c if the temperature

a car tire pressure is 2.2 bar at 25 c. if the temperature drops overnight to 5 c and if the atmospheric pressure is 1

  Finally compressed at the constant pressure to the initial

a piston-cylinder device contains 0.15kg of air initially at 2mpa and 350oc. the air is first expanded isothermally to

  A race car that weighs 2740 lb is on a circular portion of

a race car that weighs 2740 lb is on a circular portion of a track with a radius of r310 ft. the race car is traveling

  How much should mr jones put in the bank today to cover the

mr. jones plans to purchase a new 18000 automobile. he wants to borrow all the money for the car and repay it in equal

  Design a cam to move a follower at a constant velocity

Design a cam to move a follower at a constant velocity of 100 mm/sec for 2 sec and then return to its starting position with a total cycle time of 3 sec. Hint: Use a two-segment polynomial to describe the follower displacement.

  What is the maxium distance between the top of the well and

you are designing a mobile device to extract water from a well through a tube. assume your device is able to create a

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd