User Account

All Pages

Same pressure ratio and in between the fluid

Assignment Help Mechanical Engineering
Reference no: EM132058587

Humid air at 40?C and a relative humidity of 80% is compressed in a two stage compressor from 100kPa to 2500kPa. Each compressor is isentropic 1 and has the same pressure ratio and in between the fluid is cooled in an intercooler to the inlet temperature.

Will the water vapor condense in this device? Where?

What is the relative humidity at the exit of the second compressor? Draw this process for the water on a T-s diagram.

Reference no: EM132058587

Questions Cloud

Compute the volume flow rate : Gasoline flows in a long, underground pipeline at a constant temperature of 15oC. Two pumping stations at the same elevation are located 13 km apart.
What is the copr of cycle : What is the COPr of this cycle? How fast is exergy destroyed (kJ/s) in each process (evaporator, condenser, throttle, compressor)?
Consider a solar-pond power plant that operates : Consider a solar-pond power plant that operates on a simple ideal Rankine cycle with refrigerant-134a as the working fluid.
Explain and specify which category this individual best fits : Explain and specify which category this individual best fits into and why using their own behavior and track record as your examples.
Same pressure ratio and in between the fluid : Each compressor is isentropic 1 and has the same pressure ratio and in between the fluid is cooled in an intercooler to the inlet temperature.
Find the amount of heat transfer : Assume the temperature of the air inside the tank remains constant at 25°C . Find the amount of heat transfer, in kJ for the following two conditions:
Describe your various roles that exist : Describe the roles, why they are important to you and what are the expectations of those roles, why you take pride in the role.
Find the values for the cycle : The exit pressure in the first stage turbine is 0.7 MPa and it is reheated to temperature 460°C. Find the following values for the cycle:
Do you think police officer are right in being more cautious : After watching the video on "police brutality," do you think police shootings of unarmed citizens, especially minorities, are situational or deliberate?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Measured data calculate drag force per unit length cylinder

In an experiment to determine drag, a circular cylinder of diameter d was immersed in a steady two dimensional incompressible flow. Measurements of velocity and pressure were made at the boundaries of the control surface shown. The pressure was found..

  The heat of melting for water is 155 btulbm assum that all

a 2-kg block of ice with an initial temperature of -20f is dropped into an insulated tank containing 10-kg of liquid

  Exhaust gases enter the regenerator at a pressure of 140

air enters a regenerator at a pressure of 1mpa temperature of 550 k and mass flow rate of 800 kkgmin. heat is

  An insulated piston-cylinder device contains 2l of

an insulated piston-cylinder device contains 2l of saturated liquid water at a pressure of 150kpa-which is constant

  Calculate the maximum pressure that the walls must

an engine operates on an air-standard otto cycle. the pressure and temperature at the beginning of the compression

  Determine the volume change from initial state to final

a spring-loaded piston-cylinder device contains 1 kg of carbon dioxide. this system is heated from 100 kpa and 25c to

  It is necessary to maintain a pressure of 180 psi at the

at a ski resort water at 40 f is pumped through a 3-in diameter 2000ft long steel pipe from a pond at an elevation of

  What would be the amplitude

The support of a spring-mass system is vibrating with an amplitude of 6 mm and a frequency of 1200 cycles per minute. If the mass is 0.95 kg and the spring has a stiffness of 1950 N/m, determine the amplitude of vibration of the mass. If a damping..

  What specific additional data would you need from the city

What specific questions would you ask your own power plant engineer about the possibility of accepting Podunk's MSW?

  Compute the percent change n in the normal forces

Compute the percent change n in the normal forces at A and B as compared with their "engine-off" values.

  If the collar is given a speed of 4ms and the released at o

a collar having a mass of 0.75 kg and negligible size slides over the surface of a horizontal circular rod for which

  The base of the fin is maintained at a tempatrure of 220oc

a straight fin of rectangular profile has a thermal conductivity of 14 wm -oc thickness of 2.0 mm and length of 23 mm.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd