Rounded to the nearest integer that ball reaches above tee

Assignment Help Mechanical Engineering
Reference no: EM13701765

A golf ball is driven off a tee that is elevated 30 ft above the fairway and hits the ground that is below 30 ft from the tee. The initial velocity of the ball is 120 ft/s at an angle of 40 degrees from the horizontal.

Determine the maximum height, ft, rounded to the nearest integer that the ball reaches above the tee?

The distance traveled in horizontal direction, ft, rounded to the nearest integer?

 

The time of flight, s, rounded to one decimal place?

Reference no: EM13701765

Questions Cloud

Implement the network topology using packet tracer : Draw a table such as the one show below and subdivide the network into subnets Use the smallest subnet where possible and routers use G0/0 to connect to the LAN. How many MAC does the 24 port Cisco switch used in the Packet Tracer has and what is the..
Which of the following organ stores bile : Which of the following organ stores bile? spleen stomach gallbladder pancreas small intestine
Differentially expressed in the normal versus the engineer : A biotech company Helix, has obtained tissue from normal mice and from mice that have especially engineered, highly active muscle cells. You are hired by the company to identify the genes (mRNA) that are differentially expressed in the normal ..
What biochemical function does the enzyme serve : The enzyme pectinase:  what biochemical function does the enzyme serve? What reaction does it catalyze and why is it important to the food industry?  how is the enzyme used in the food industry?
Rounded to the nearest integer that ball reaches above tee : A golf ball is driven off a tee that is elevated 30 ft above the fairway and hits the ground that is below 30 ft from the tee. The initial velocity of the ball is 120 ft/s at an angle of 40 degrees from the horizontal.
Load of chemicals hits the front edge of the fire : You are a pilot of a plane fighting a forest fire, you are flying 1000ft above the ground at a speed of 90 miles per hour and are going to drop a 5000 pound load of fire suppressing chemicals onto the fire, how far from the front line of the fire mus..
All devices have the same amount of energy : There are three copper blocks, A, B, and C, containing 10 kJ of energy at 600 C, 200 C, and 100C, respectively, and a fourth iron block, D, containing 10 kJ of mechanical energy. (Thus, all devices have the same amount of energy.) The surrounding tem..
Pretend that you are participating in a public safety awaren : Pretend that you are participating in a public safety awareness forum and that you have been selected to deliver a presentation on the health risks of one of the toxic substance categories that we have covered in this unit. (A power point)
Find natural frequency and resonant frequency : You have a spring-mass-damper-system, where when the 200g mass was hung on the spring-damper assembly, it deflected by 2 cm. Find natural frequency? Find resonant frequency

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd