Results for the local heat transfer coefficient

Assignment Help Mechanical Engineering
Reference no: EM13946596

Experimental results for the local heat transfer coefficient hfor flow over a flat plate with an extremely rough surface were found to fit the relation

hx(x) = ax-0.1

where is a coefficient (W/m1.9 · K) and (m) is the distance from the leading edge of the plate.

1. Develop an expression for the ratio of the average heat transfer coefficient hfor a plate of length to the local heat transfer coefficient hat x.

2. Plot the variation of hand has a function of x.

Reference no: EM13946596

Questions Cloud

Find the height to which the water can be delivered : Find the height to which the water can be delivered - A centrifugal pump delivers water at the rate of 0.22 m3/s from a reservoir at ground level toanother reservoir at a height H, through a vertical pipe of 0.2m diameter.
Determining the approximate water temperature : Water flows at a velocity uoo = 1 m/s over a flat plate of length L = 0.6 m. Consider two cases, one for which the water temperature is approximately 300 K and the other for an approximate water temperature of 350 K. In the laminar and turbulent r..
Metallurgical engineer : A metallurgical engineer decides to set aside money for his newborn daughter's college education.
Famed boston rock and roll club euphoria : On May 1, 1995, the famed Boston rock and roll club Euphoria burned to the ground. Luckily, the fire began at 2:00 a.m. and no one was injured. The highly anticipated and sold out May 2, 1995, concert of the New York rock group Zephyr was cancelle..
Results for the local heat transfer coefficient : Experimental results for the local heat transfer coefficient hx for flow over a flat plate with an extremely rough surface were found to fit the relation
Which has access to the raw message : Please answer this post like discussion if you agree or disagree, and why? Please explain it. This post is the answer from somebody else about question
Analyse a selection of relevant management theories : Analyse a selection of relevant management theories in context of your organisation and compile a series of recommendations for that organisation that would enhance practice of management of one of topics selected.
Morten construction company provides construction : Morten Construction Company provides construction services for major projects. Managers at the company believe that construction is a people-management business,
Diligence and prepared for each individual audience sector : Let's continue with the scenario from Discussion Question 2. Now that you have done your due diligence and prepared for each individual audience sector, it's time to visit the university and sell your electronic tablet!

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd