User Account

All Pages

Required input power of the pump

Assignment Help Mechanical Engineering
Reference no: EM13886268

A pump is located between two reaches of horizontal piping. The conditions upstream of the pump are D1 ¼ 75 mm and p1 ¼ 450 kPa, and downstream of the pump D2 ¼ 100 mm and p2 ¼ 900 kPa. For a discharge of Q ¼ 100 L=min and a loss across the pump of hL ¼ 7 m, what is the required input power of the pump if its ef?ciency is 78%?

Reference no: EM13886268

Questions Cloud

Chemical and physical properties : In our world today, aluminum is used for many items, including beach chairs and soda cans. This material was not chosen randomly but was carefully selected based on many variables. Think about where aluminum comes from, how we obtain/purify it and it..
What is a cartel? is cartel good for our economy? : What is a Cartel? Is Cartel good for our economy?
Determine posterior predictive probability and extreme value : Determine the posterior predictive probability P(y > .5/ y1,.... , y120) (the probability of a dangerous mercury level) and also the extreme value P(y > 3.0/y1, . . . , y120).
What speed should be selected for a wind tunnel model : A proposed model study of a low-speed aircraft is to be performed using a 1:10 scale model. If the prototype is to travel at 25 m=s, what speed should be selected for a wind tunnel model? Is such a test advisable?
Required input power of the pump : For a discharge of Q ¼ 100 L=min and a loss across the pump of hL ¼ 7 m, what is the required input power of the pump if its ef?ciency is 78%?
Identify the consequences of the actions : Consider these three problems. In writing a paper about all three of them individually, identify the consequences of the actions taken, and then determine whether the actions taken represented a greater good, who would benefit from the good, and whet..
Wide range of environmental conditions : Humans are able to control their heat production rate and heat loss rate to maintain a nearly constant core temperature of under a wide range of environmental conditions.
Identify the characteristics of false reports of crime : Demonstrate deductive reasoning and critical thinking skills through application in hypothetical examples of criminal behavior. Identify the characteristics of false reports of crime and staged crime scenes
Determine the effects of the dimples : A model of a golf ball is to be studied to determine the effects of the dimples. A sphere 10 times larger than an actual golf ball is used in the wind tunnel study. What speed should be selected for the model to simulate a prototype speed of 50 m=..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Diameter pipeline terminates in a nozzle of outlet diameter

A 0.3-m diameter pipeline terminates in a nozzle of outlet diameter = 0.15 m. When water flows through this pipe at a rate of 0.25 m3 /s, the force required to hold the pipe (N) is most nearly.

  A heat engine operates between reservoirs

A heat engine operates between reservoirs at 1000 and 300 K. Some of the power output from the heat engine drives a refrigerator which operates between 250 and 300 K. The heat-transfer input at 1000 K to the heat engine is 1000 kJ, and the heat trans..

  In dribbling the player compensates for the mechanical

a basketball of mass 0.570 kg is dropped from rest from a height of 1.25 m. it rebounds to a height of 0.734 m. a how

  A 30-kg aluminum block initially at 140 c is brought into

a 30-kg aluminum block initially at 140 c is brought into contact with a 40-kg block of iron at 60 c in an insulated

  Assuming that the fluid water is at a temp of 80 f and

measuring a velocity gradient at the surface of a 100 ft2 plate to be 0.5362 sec-1 i assume that this is a typo so i

  In a spring mass system a 1kg block is dropped from a

in a spring mass system a 1kg block is dropped from a height of 1 meter on top of a spring with a spring constant k

  Determine the exegetic efficiency

Hydrogen at 25 bar, 450°C enters an adiabatic turbine and expands to 2 bar, 160°C with a mass flow rate of 0.2 kg/s. For a dead state of To= 25°C, Po = 1 atm determine the exegetic efficiency.

  Estimate the required filter length for a bed efficiency

a fibrous filter bed is to be designed with a solid fraction equal to 0.1 fiber diameter equal to 10m and filter

  Calculate the area of the hole in the tube

A slow leak develops in an inner tube (volume, 0.5 ft3, temperature, 600F), wherein it takes 4 hours for the pressure to decrease from 30 to 25 psig. The mass flow rate of air per second under the conditions is given by 0.68pA/(RT)0.5, where the unit..

  In order to have the machine deliver 100000 nmkg of air

air enters a machine at 373 k with a speed of 200 msec and leaves it at the temperature of the standard sea level

  A helical spring of stiffness k is cut into two halves and

mechanical vibrations a helical spring of stiffness k is cut into two halves and a mass m is connected to be 0.5 s. if

  If the volume flow rate at the exit is 15 m3s the inlet

an adiabatic gas turbine expands air at 3447 kpa and 427degc to 415 kpa and 120degc. if the volume flow rate at the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd