Replacing about half of the steel-based materials

Assignment Help Mechanical Engineering
Reference no: EM13707817

Replacing about half of the steel-based materials in a car can reduce the weight of the vehicle by almost 60%. This can lead to nearly a 30% increase in fuel efficiency. What kinds of materials could replace steel in cars (pick at least two)? What would be the advantages and disadvantages in using these materials as replacements for steel?

Reference no: EM13707817

Questions Cloud

Draw the structures of the three alkenes : Problem- The treatment of 3-methyl-2-phenyl-pentan-3-ol with concentrated sulferic acid results in three possible alkenes. a. Draw the structures of the three alkenes.
Calculate the specific gravity of the missing fluid : Consider this multi-fluid container that contains fluids of different SGs as shown except for one fluid. Given that the pressure measured by the gage is 15.5 psia and the pressure in the container is 108.55 kPa, calculate the specific gravity of the ..
A playground ride consists of a disk of mass m : A playground ride consists of a disk of mass M = 43 kg and radius R = 2.4 m mounted on a low-friction axle. A child of mass m = 16 kg runs at speed v = 2.7 m/s on a line tangential to the disk and jumps onto the outer edge of the disk.
What is the ph of the solution : Problem- The hydronium ion concentration of a 0.010 M acetic acid solution is 4.2 x 10-4 M. What is the pH of the solution
Replacing about half of the steel-based materials : Replacing about half of the steel-based materials in a car can reduce the weight of the vehicle by almost 60%. This can lead to nearly a 30% increase in fuel efficiency. What kinds of materials could replace steel in cars (pick at least two)? What wo..
How many electrons pass through the bulb : Problem- A light bulb draws a steady current of 9.5 x 10-2 A. How many electrons pass through the bulb in 1.00 hr?
Degree-of-freedom analysis and estimate the molar flow rate : A stream of humid air containing 1.00 mole % H2O(v) and the balance dry air is to be humidified to a water content of 10.0 mole % H2O. For this purpose, liquid water is fed through a flow meter and evaporated into the air stream. The flow meter readi..
What is the volume of the solution : Problem- If 0.0280 mol of CaCl2 is dissolved in water to make a 0.710 M solution, what is the volume of the solution?
Business management assignment : Anderson Ltd manufacture gearboxes for use in cars. At the start of the year, the management of Anderson Ltd. estimated that its costs would be

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the intermediate pressures that minimize the

consider a three stage compression process with intercooling and determine the intermediate pressures that minimize the

  A diffuser shown in fig p636 has air entering at 100 kpa

a diffuser shown in fig. p6.36 has air entering at 100 kpa 300 k with a velocity of 200 ms. the inlet cross-sectional

  Ignoring the heat transfer changes in potential energy and

hot air steadily enters a gas turbine at 5 bar 900 k and exits at 1 bar 600 k and a velocity of 100 ms. the mass flow

  Calculate the final temperature of the copper block

A 1-kg copper block at the initial temperature of 527 degrees C has been placed inside a perfectly insulated vessel containing 10 kg of water at the initial temperature of 27degrees C. The final temperature of the copper block is measured after the s..

  Some other heat is also transferred at 200degc calculate

ater enters a reversible steady-state device at 125degc and 400 kpa and leaves at 300degc and 200 kpa. heat is added

  Convert the value above to a gallons per hour figure if

you are looking for a power unit to run an irrigation pump in your operation. the pump requires 92 horsepower to turn

  A steam power plant receives 1000 btus in the boiler at

a steam power plant receives 1000 btus in the boiler at 1250 f and discharges 600 btus in the condenser at 80 f. the

  A smoke stream from a smoke generating tube is often used

a smoke stream from a smoke generating tube is often used as a simple method of flow visualization in wind tunnels.

  Determine the time taken for the product to freeze if it is

a fruit juice containing 30 solids of molecular weight 100 g was placed in a tray length 100 cm height 90 cm width 8

  Determine a the components of the force f exerted by the

a nozzle discharges a stream of water of cross-sectional area a with a velocity va. the stream is deected by a single

  Draw the complete mohr circle and sigma1sigma2 plot what is

a machine component is made of 2024-t4 aluminum. the external loads produce highest operating principle stresses that

  The axis of rotation is through the center of the round

an external moment of 500 n-m is applied to the composite plate in clockwise direction as shown. the square plate is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd