Regenerator effectiveness-the cycle thermal efficiency

Assignment Help Mechanical Engineering
Reference no: EM13709111

Air is compressed from 23 C to 100 kPa to 500 kPa in a gas turbine. The air is heated to 520 C in the regenerator and then to 1200 C before entering the turbine. The isentropic efficiency is 100% for both the compressor and turbine. Please draw and label the T-s diagram, determine the regenerator effectiveness, the cycle thermal efficiency and the back work ratio.

Reference no: EM13709111

Questions Cloud

Calculate the velocity at the exit of the nossels : The stators in a gas turbine are designed to increase the kinetic energy of the gas passing through them adiabatically. Air enters a set of these nossels at 270 psia and 795 F with a velocity of 97 ft/s and exists at 200 psia and 550 F. Calculate the..
What was the ray angle of incidence on the crystal : A costume jewelry pendant made of cubic zirconia is submerged in oil. What was the ray's angle of incidence on the crystal
What is the pressure exerted by the gas on the wall : A sealed container has a volume V=0.008 cubic meters and 3 times Avogadro's number of molecules at a temperature T=20 degrees Celsius. What is the pressure P exerted by the gas on the wall of the container
Determine the resistance of the fluid in this axon : Some human nerve cells have a long, thin cylindrical cable (the axon) from their inputs to their outputs. Consider an axon of radius 5.5x10-6m length 0.64m. Determine the resistance of the fluid in this axon
Regenerator effectiveness-the cycle thermal efficiency : Air is compressed from 23 C to 100 kPa to 500 kPa in a gas turbine. The air is heated to 520 C in the regenerator and then to 1200 C before entering the turbine. The isentropic efficiency is 100% for both the compressor and turbine. Please draw and l..
Evaluate the total distance covered : A subway train starts from rest at a station and accelerates at a rate of 1.70m/s2 for 14.0s. Find the total distance covered
What is the resistance : A glass capillary tube with a diameter of 0.42 mm and length 11 cm is filled with a salt solution with a resistivity of 0.20 ohm•m. What is the resistance
Determine the work output-isentropic efficiency of the cycle : In a reheat rankine cycle, steam enters the turbine at 4 MPa and 400 C. After expanding to 400 kPa, the steam is reheated again to 400 C, and expands in the low pressure turbine to 10 kPa. If the efficiency of the turbine and the pump is 100% and the..
Find the electric flux through the surface of the box : A long straight line of charge has a uniform positive charge per unit length λ. Find the electric flux through the surface of the box

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd