Range of wavelengths of visible light

Assignment Help Mechanical Engineering
Reference no: EM13948179

1. Zinc selenide has a band gap of 2.58 eV. Over what range of wavelengths of visible light is it transparent?

2. Briefly explain why the magnitude of the ab- sorption coefficient (b in Equation 21.18) depends on the radiation wavelength.

3. The fraction of nonreflected radiation that is transmitted through a 5-mm thickness of a transparent material is 0.95. If the thickness is increased to 12 mm, what fraction of light will be transmitted?

Transmission

4. Derive Equation 21.19, starting from other expressions given in the chapter.

5. The transmissivity of a transparent mate- rial 15 mm thick to normally incident light is 0.80. If the index of refraction of this mate- rial is 1.5, compute the thickness of material that will yield a transmissivity of 0.70. All reflection losses should be   considered.

Reference no: EM13948179

Questions Cloud

What statistical test should be used to analyze these data : What statistical test should be used to analyze these data? Identify H0 and Ha for this study. Conduct the appropriate analysis.
Phenomenon of luminescence : 1. (a) In your own words describe briefly the phenomenon of luminescence. (b) What is the distinction between fluores- cence and phosphorescence?
Mechanisms in nonmetallic materials : Briefly describe the three absorption mechanisms in nonmetallic materials.
Construct and interpret a 92% condidence interval for p : Carry out an appropriate text at a 5% level of significance to test george and Jerry's theory. Interpret the p-value you calculated in part A. Construct and interpret a 92% condidence interval for P.
Range of wavelengths of visible light : 1. Zinc selenide has a band gap of 2.58 eV. Over what range of wavelengths of visible light is it transparent? 2. Briefly explain why the magnitude of the ab- sorption coefficient (b in Equation 21.18) depends on the radiation wavelength.
Find definitions of the thinking process : Search the Internet, and find definitions of the thinking process and the indicated thinking process tools. List some of the benefits achieved by these companies. Is TOC more than an inventory management method?
Losses of transparent materials : 1. It is desired that the reflectivity of light at normal incidence to the surface of a trans- parent medium be less than 5.0%. Which of the following materials in Table 21.1 are likely candidates: soda-lime glass, Pyrex glass, periclase, spinel,..
Application: ethics in diverse hiring practices : This week's readings have dealt with the important issues of ethics, diversity, and social responsibility. Many people consider these issues to be inter-related or overlapping aspects of doing business in the 21st century. An organization's divers..
Identify the best method for deriving duration : Analyze the given scenario and identify the best method for deriving duration estimates for project activities. Why did you think the one you selected is better than the other methods

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A hot-water stream at 80 degrees c enters a mixing chamber

a hot-water stream at 80 degrees c enters a mixing chamber with a mass flow rate of 0.5 kgs where it is mixed with a

  Calculate the magnitude of mans acceleration

If the speed of the man at A (XA = 5m and YA = 1m) is VA = 9 m/s and the increase of his speed is dVA/dt = 13 m/s2, calculate the magnitude of his acceleration and the slop angle at this point.

  Determine the velocity of the water issuing from the

the closed tank is pressurized at 15 psig by air as shown. the liquid is water. determine the velocity of the water

  Fluid is moving between two plates the top plate

Fluid is moving between two plates the top plate is moving with a velocity V, the distance between the plates is h, and the flow is completely horizontal; select the appropriate boundary condition of the viscous flow.

  Calculate the service factor for a simple lawn mower driven

Calculate the service factor for a simple lawn mower driven by a two stroke engine. The lawn mower is used by a service for 8 hours per day. If the lawnmower normally operates at 1200 rpm and 2 hp what is the starting torque?

  Determine the maximum allowable tensile load before

a 1 meter section of 1040 steel square tubing is loaded in tesnion. the tubing has an outer edge length of 10mm and a

  Calculate the work done when a gas expands from 350 kpa and

during some actual expansion and compression processes in piston-cylinder devices the gases have been observed to

  Takes for the parcel to reach the speed of the belt

A parcel is lowered onto a conveyor belt that is moving at 4 m/s. If the coefficient of kinetic friction between the parcel and the belt is 0.25, calculate the time that it takes for the parcel to reach the speed of the belt.

  Determine the distance the cart will move down the inclined

the 20-lb car is released from rest at time t0 on the inclined surface. the force p 8t lb acts on the cart where t is

  An ideal diesel cycle with air as the working fluid has a

an ideal diesel cycle with air as the working fluid has a compression ratio of 20 and a cutoff ratio 2.1. at the

  What is the isentropic efficiency

H2O at 350oF, 60 psi enters an insulated nozzle at 10 ft/s. It leaves at 1440 ft/s and 35 psi.  What is the isentropic efficiency?

  A particle moves along the curve yx2 - 4m with a constant

a particle moves along the curve yx2 - 4m with a constant speed of 5 ms. determine the point on the curve where the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd