Range of acceptable power dissipation for the package

Assignment Help Mechanical Engineering
Reference no: EM131281613

An instrumentation package has a spherical outer surface of diameter D = mm and emissivity ε = 0.25. The package is placed in a large space simulation chamber whose walls are maintained at 77 K. If operation of the electronic components is restricted to the temperature range 40 ≤ T ≤ 85°C, what is the range of acceptable power dissipation for the package? Display your results graphically, showing also the effect of variations in the emissivity by considering values of 0.20 and 0.30.

Reference no: EM131281613

Questions Cloud

Are all workers with occupational injuries protected by ada : Are individuals who are perceived as having handicaps, but in fact either have recovered from the disability or are not handicapped, covered by the Rehabilitation Act of the ADA ?- Are all workers with occupational injuries protected by the ADA?
What factors must be proved to establish the case : Mazir Coleman drove a school bus for the Casey County, Kentucky, Board of Education for four years.- What factors must be proved to establish his case? Decide.
What is its surface temperature : If the probe surface has an  emissivity of 0.8 and the probe does not receive radiation from other surfaces, as, for example, from the sun, what is its surface temperature?
What factors must the court consider : What factors must the court consider in evaluating Heron's claim? What result should the court reach in this case? Decide.
Range of acceptable power dissipation for the package : Display your results graphically, showing also the effect of variations in the emissivity by considering values of 0.20 and 0.30.
Analyze reasons why third parties have never been successful : Identify three to four ideological differences between America's two major political parties. Analyze key reasons why third parties have never been successful at the presidential level.
What is the paradox of thrift : What is the paradox of thrift? Is Saving Good or Bad?Is it real? What is the reverse paradox of thrift?
Which one is an abundant product of weathering : Which one of the following is an abundant product of weathering? Which of the following describes a mineral's tendency to split along smooth, parallel planes of atomic weakness?
Did the company violate the ada by treating individuals : Did the company violate the ADA by treating individuals with job-related disabilities differently from an individual with a disability caused by an off-the-job accident? Decide.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd