User Account

All Pages

Rake angle15degree cutting force500n and thrust force200n

Assignment Help Mechanical Engineering
Reference no: EM13639786

An orthogonal cutting operation is being carried out under the following conditions: depth of cut= 0.15mm, width of cut=5mm, chip thickness =0.2 mm, cutting speed=2m/s, rake angle=15degree, cutting force=500N and thrust force=200N. Calculate the percantage of the total energy that is dissipated in the shear plane during cutting?

Reference no: EM13639786

Questions Cloud

Determine a the number of cycles executed per minute and b : each cycle the working fluid of a sterling engine receives 2.67 kj of energy in the heat interaction with its
Suppose the lifetime of a particular appliance follows an : 1 the number of customers at quiet morning bakery is believed to follow a poisson distribution with a mean of 2
Heating continues until no liquid remains in the tank : the rigid tank in the figure below has a volume of 60 l and initially contains a two-phase liquid vapor mixture of h20
There is a 10 chance of the part being defective if : company a provides a critical manufacturing part 30 of the time company b provides the same part 50 of the time and
Rake angle15degree cutting force500n and thrust force200n : an orthogonal cutting operation is being carried out under the following conditions depth of cut 0.15mm width of cut5mm
The monthly earnings of computer programmers are normally : the monthly earnings of computer programmers are normally distributed with a mean of 4000. if only 1.7 of programmers
During this time three forces act on the boat a 333-n force : a 343-kg boat is sailing 17.0 deg north of east at a speed of 2.20 ms. 33.0 s later it is sailing 33.0 deg north of
A 200 l sample of air at -50 degreees c has a pressure of : a 2.00 l sample of air at -50 degreees c has a pressure of 700 torr. what will be the new pressure in torr if the temp
Suppose that two fair ie the probability of both heads and : suppose that two fair i.e. the probability of both heads and tails is 0.5 coins are tossed and we observe the results.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The turbine isentropic efficiency is 075 calculate the

a geothermal power plant utilizes steam produced by natural means underground. steam wells arc drilled to tap this

  Consider fully developed laminar flow with constant

consider fully developed laminar flow with constant properties in a circular tube. let the surface be insulated but let

  What is ductile-to-brittle transition temperature describe

what is ductile-to-brittle transition temperature? describe a method to determine ductile-to-brittle transition

  Dtermine a the velocity when x 2mb the position where the

the acceleration of the particle is defined by the relation a 25-3x2 where a is expressed in msec2 and x in meters. the

  Using the kelvin-planck statement of the second law of

using the kelvin-planck statement of the second law of thermodynamics demonstrate the following corollary. the

  A shell-and-tube heat exchanger must be designed to heat 25

a shell-and-tube heat exchanger must be designed to heat 2.5 kgs of water from 15 to 85 oc. the heating is to be

  Determine the entropy generation kjkg-k for the compressor

saturated liquid water is compressed from 100 kpa state 1 to 2.5 mpa state 2 in an adiabatic pump having 85 isentropic

  C is to be 375 units and is to be directed at 75 degrees

resolve a vector a which has a magnitude of 50 units and a direction of 210 degrees into two vetors b and c. c is to be

  Evaluate the maximum bending moment

Draw the shear force diagram for the beam and determine the position and magnitude of the maximum bending moment.

  Find the power input to the compressor suppose on an actual

air flows through an adiabatic internally reversible compressor at a rate of 0.04 kgs. at the inlet thepressure is 200

  The second shaft is hollow with an outside diameter of 3 in

two steel shafts are made of cold-drawn steels having ultimate tensile strengths of 185 kpsi and 240 kpsi respectively.

  Calculate the increase in entropy which occurs when the

a rigid container is divided into two compartments of equal volume by a partition. one compartment contains 1 mole of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd