Qestion 1if the velocity potential can be described byphi

Assignment Help Mechanical Engineering
Reference no: EM13373558

Question 1

If the velocity potential can be described by

Φ = -b/4 (x-y)(x +y)

where b is some constant, what is the formula for the stream function? Sketch the flow pattern.

Question 2

The following measurements have been taken at sea level for a model aeroplane whose propeller had a diameter of 20 cm and was flying at 54 km/hr:

Propeller speed (rpm)

2400

3000

4500

Thrust force (N)

4.2

5.4

8

(a) Assume that viscous effects are negligible

(i) Plot this data using appropriate dimensionless groups

(ii) Determine the thrust of a similar aeroplane whose propeller has a 1.3 m diameter, spinning at 1500 rpm while flying at 300 ktn/hr at 3250 m altitude.

(b) Repeat pall (a) assuming that viscous effects are dominant.

Question 3

A petrol tanker uses gravity to empty its 35 kL tank into an underground storage tank. The hose that is used has a roughness equivalent to galvanised iron, has an internal diameter of 10 cm and is 10 m long (see figure). The centreline of the square hose fitting on the tanker is mounted 50 cm off the ground, while the hose penetrates 2 m below ground level. All bends have a radius of curvature of 15 cm. It is claimed that the tank can be emptied within 30 min: verify whether this claim is correct.

Reference no: EM13373558

Questions Cloud

To deal with deadlocks we can either use prevention or : to deal with deadlocks we can either use prevention or avoidance or detection followed by recovery. but which is a
Part a consider the information below from a firms balance : part a consider the information below from a firms balance sheet for 2011 and 2012.current assets20122011change cash
1 choose an online newspaper article use the elements of : 1 . choose an online newspaper article. use the elements of reasoning model to analyze the logic of the article. your
Whether or not you ever actually conduct an interview for : whether or not you ever actually conduct an interview for this lesson you need to submit 20 questions to fulfill the
Qestion 1if the velocity potential can be described byphi : question 1if the velocity potential can be described byphi -b4 x-yx ywhere b is some constant what is the formula for
Nbspedit each sentences below to eliminate ambiguities in : nbspedit each sentences below to eliminate ambiguities in pronoun referencs or to clarify ambiguous modifiers. a bill
Write a photo essay based off of your interactions with : write a photo essay based off of your interactions with jane jacobs death and life of great american cities. the
One work of historical fiction or nonfiction aimed at : one work of historical fiction or nonfiction aimed at children relative to the following elementsall key elements of
Assignment suppose you are the information security : assignment suppose you are the information security director at a small software company. the organization currently

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd