Reference no: EM131204981
Lab: Diode Forward Bias Curves
Purpose
In this lab you will observe the forward voltage drop of the diode as a function of current for two diodes. In addition you will learn how to use the function generator, both oscilloscope channels simultaneously, and use the cursors.
Equipment
1. Function Generator (FG)
2. Oscilloscope
Materials
1. 100 Ω Resistor
2. 330 Ω Resistor
3. 1N4002 Diode
4. Red Light Emitting Diode (LED) (Provided in Lab)
Procedure
1. Directly connect the Function Generator to channel 1 of the oscilloscope and configure it to provide a Sawtooth Wave with the following parameters:
Settings:
a. A Maximum Voltage of +4V
b. A Minimum Voltage of -1V
c. A Frequency of 100Hz
To do this start by selecting the ‘Wave Gen' button, WAVE = RAMP, FREQ = 100 Hz, AMPLITUDE = 5.0V, Offset ≅ 1.50V, SYMMETRY (Duty Cycle) = 100%
2. Once the Function Generator is properly configured, construct the circuit as shown on the previous page. Remember that when the Function Generator is used the red clip is the positive terminal and the black clip is the negative terminal. At this time use the 1N4002 Silicon Diode as D. [Note that for the 1N4002 the lead closest to the white band is cathode and corresponds to the line seen with the diode in circuit diagrams. For glass cased diodes (such as the Zener) the band is black. Just remember that the lead closest to the band is the cathode.] Connect channel 1 of the oscilloscope to node 1 on the circuit diagram and channel 2 to node 2. Connect the black alligator clip from the oscilloscope probes to node 0 of the circuit.
3. Adjust the oscilloscope settings until you have a good view of one to two cycle(s) of the two resulting waveforms. Once this is done press SINGLE on the scope to have it take one "reading" to make it easier to look at. (Make sure channel 1 and channel 2 are both set to 2V/div.) Use the cursors to probe the wave and take measurements of the voltages that you see on both waveforms. Take measurements of both at the following points: V1 = -1V, 0V, +1V, +2V, +3V, +4V
To utilize the cursor feature, select the ‘Cursors' button, MODE = TRACK WAVEFORM, X1 SOURCE = 1, X2 SOURCE = 2. First set CURSORS = X1 and move the cross hairs to -1V, then set CURSORS = X2 and move the cross hairs until they align with X1 (ΔX = 0.00 s), the set CURSORS = X1X2 LINKED. Then you will be able to measure V1 and VD simultaneously at the points requested above.
4. Disconnect the FG and probes from the circuit and replace the 1N4002 diode with the red LED and the 100Ω for the 330Ω resistor. Note: The cathode end of the LED is indicated with a flat edge on the plastic casing and a shorter leg. Turn the FG back on and repeat step 3.
Submittal:
Provide a table that contains each pair of voltage measurements that you took (the source and diode voltages). For each pair calculate the current flowing in the circuit at that time. Discuss your observations of the data and talk briefly about the differences between the 1N4002 and the LED. Nothing you submit should be hand-written.
This lab submittal will consist of two circuits, one table (including measured and calculated data), any general equations (or sample equations) used to calculate any data in the table, and a ‘DISCUSSION' section. Find (and submit) the datasheet of the LED, Kingbright WP7113SRD/E and the 1N4002 diode, and include in your discussion the expected forward current and voltage of each diode from the datasheet compared to measured results.
|
Culture and corporate ethics
: Recently ITT Technical institute announced that it would be shutting down it's educational centers (Korn and Jamerson, 2016). Read about it here" http://www.wsj.com/articles/itt-technical-institute-to-close-after-government-cuts-off-new-funding-1473..
|
|
Acquires assets with a basis to green corporation
: Brown Corporation purchased 85% of the stock of Green Corporation five years ago for $850,000. In the current year, Brown Corporation liquidates Green Corporation and acquires assets with a basis to Green Corporation of $700,000 (fair market value of..
|
|
Total cost at time zero of accepting
: Stanton's marginal tax rate is 40 percent. Stanton expects the equipment will have a marekt salvage value of $10,000 at the end of 4 years. What is the Total Cost at Time Zero of accepting this prject?
|
|
Determine the net cash flows from operating activities
: Last year Emmons Company reported cost of goods sold of $115,000. Inventories decreased by $20,000 during the year, and accounts payable decreased by $15,000. The company uses the direct method to determine the net cash flows from operating activitie..
|
|
Provide table that contain each pair of voltage measurements
: Provide a table that contains each pair of voltage measurements that you took (the source and diode voltages). For each pair calculate the current flowing in the circuit at that time.
|
|
What are the 8 characteristics typical of primates as mammal
: What do primatologists study to trace evolution? Do they observe primates in natural environments or in captivity?
|
|
Compute the length of stay
: Compute the length of stay of 10 patients who were discharged from hospital on October 5, 2008. Their dates of admission were as follows:
|
|
About the four functions of management
: Based on what you have learned about the four functions of management and how they are interrelated, share a real world example of where you have seen these functions in action either successfully or unsuccessfully
|
|
Different types of organizations behind the project
: Choose three project knowledge areas, and consider how the project might be affected in each of these areas by the different types of organizations behind the project. Write a few paragraphs on this topic to organize your thoughts on the subject.
|