User Account

All Pages

Prove using the increse in entropy principle that the

Assignment Help Mechanical Engineering
Reference no: EM13623630

a) Two thermal reservoirs are placed in contact with each other. Prove from the increase of entropy principle that heat transfer will be in the direction of high temperature to low temperature.

b) Prove using the increse in entropy principle that the maximum thermal efficiency for any heat engine is the Carnot efficiency.

c) Using the Tds equations to show that the polytropic exponent of an ideal gas undergoing an isentropic process is k( the ratio of specific heats).

Reference no: EM13623630

Questions Cloud

The following data were collected for a test of linear : the following data were collected for a test of linear correlation and spearmans rank correlation was used2.2 3.3 3.3
What is the gauge pressure of the gas in this mercury : what is the gauge pressure of the gas in this mercury manometer if h 81 mm and the atmospheric pressure is 773 mmhg?
After the collision the 020-kg puck has a speed of 15 ms at : a 0.30-kg puck initially at rest on a frictionless horizontal surface is struck by a 0.20-kg puck that is initially
What test is appropriate for this problem state the null : a lab is comparing a test drug to a standard drug that is useful to patients having high blood pressure. the standard
Prove using the increse in entropy principle that the : a two thermal reservoirs are placed in contact with each other. prove from the increase of entropy principle that heat
Find the best predicted temperature at a time when a : 1. one classic application of correlation involves the association between the temperature and the number of times a
The space between the concentric spheres is filled with a : a spherical capacitor has an inner sphere of radius 12 cm and an outer sphere of radius 13 cm. the outer sphere is
The premissible stresses in the key are 55 nmm2 in shear : a belt pulley is fastened to a 75 mm shaft running at 360 rpm by means of a key 18 mm wide and 125 mm long. the
Show that the force on each plate of a parallel plate : show that the force on each plate of a parallel plate capacitor has a magnitude equal to 12 qe where q is the charge on

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What are the possible outcomes of this scenario

What are the possible outcomes of this scenario?

  Determine the fraction of the prototype speed in air at

measurements of drag force are made on a model automobile in a towing tank filled with fresh water. the model length is

  Air at 80f and standard atmospheric pressure flows through

air at 80f and standard atmospheric pressure flows through a furnace filter with an average velocity of 2.4 fts. the

  Calculate the height h to which the ball rises

A ball is thrown vertically up with a velocity of 91 ft/sec at the edge of a 190-ft cliff. Calculate (a) the height h to which the ball rises and (b) the total time t after release for the ball to reach the bottom of the cliff.

  If the specific heat of brass c is 0385 kjkgk determine the

brass balls each of mass 0.258 kg and initially at 130degc are quenched in a water bath at 50degc for 2 minutes at a

  Describe on your own words the three strengthen mechanism

describe on your own words the three strengthen mechanism for metals i.e. grain size reduction solid solution

  What is the percentage error

One side of a right triangle is known to be 45 cm long and the opposite angle is measured as 30?, with a possible error of 1?.

  If it suddenly exposed to a convection environment at 50 c

a long aluminum bar has a diameter of 11 cm and is initially uniform in temperature at 300 c. if it suddenly exposed to

  Derive the following a differential equation between input

the following data were observed in a step response experiment of a thermometer is under a step input from 0 degress c

  What is the strain when the load is applied

What will be the length of the specimen after the load is removed? d) The specimen was reloaded until fracture. If the % reduction in area after fracture was 40%, what is the minimum diameter of the specimen at fracture?

  Computing electrical power from a geothermal resource

Calculating electrical power from a geothermal Resource, A geothermal well is producing 9000kg/second from a hot water basin at 200 ºC [enthalpy of 800 KJ/Kg].

  Find a suitable generating function

Prove that the transformation Q1 = q12 Q2 = q2 sec p2 p cos p2 - 2q2 P= 1 P2 = sin p2 - 2q1 1 2q1 cos p2 is canonical, by any method you choose . Find a suitable generating function that will lead to this transformation.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd