Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Procedure:
Design the following circuit and code:
Modify the Bar Graph Distance Control circuit and program to using a photoresistor input instead of an IR distance sensor in
Chapter 3 (pp. 56- 59). Modify the program to represent an illumination LED bar graph circuit. In other words, when the photoresistor detects maximum light, all of the eight LEDS light. As you dim the amount to the photoresistor, the LEDS start to turn off from right to left.Send your code file (.ino) of the lab completed and operational as well for credit.
Analysis/Discussion:
Explain what you did in the program to reverse the display of the bar graph, making the bar graph illuminate with the LEDS on and turning off as you dimmed the light.
The 74HC595 shift register is essential converting 3 inputs to 8 outputs. In your own words, how does this work?
Attachment:- 1613393_1_pp-56-59.pdf
An essay about multi-band wearable antenna for health care services. Minimum of 3 pages and with references/citation.
A station running TCP/IP needs to transfer a file to a host. The file contains 2048 bytes. How many bytes, including all of the TCP/IP overhead, would be sent, assuming a payload size of 512 bytes and that both systems are running IPv4
Plot how this absorbed power varies with signal strength W12, and discuss the behavior especially at very small and very large W12. Where does the absorbed power go? -and how does it get there?
Find Rin, Avo, and Ro. Also, if a load resistance of 10k ohm is connected to the output, what overall voltage gain Gv is realized. Now, if a 0.2 V peak sine wave signal is required at the output, what must the peak amplitude of Vsig be.
A young designer, aiming to develop intuition concerning conducting paths within an integrated circuit, examines the end-to-endresistance of a connecting bar 10μm long, 3μm wide, and1μm thick, made of various materials.
A process has dynamics G(s)=1/(4s^s+s+1). Apply a unity negative feedvack controller of the form G.c(s)=1/(s+b). (a) Report the transfer function T(s) of the closed-loop system. (b) Report T(s) to 2nd order and report the reduced transfer function T..
1. The net charge through a cross section of a circuit element is given by q(t)=2t+t^2 C. As usual, t is in seconds. Find the current through the element in amperes. 2. the current through a given circuit element is given by i(t)=2e^-t A. As usual..
Two non-EE students, Juan and Jose, living in neighboring rooms ina boarding house, decided to economize by connecting their ceilinglights in series. They agree that each installs a 100 W bulb in their rooms and that they would pay equal shares of..
An optimizing compiler has been developing for the bad store machine with a measurement shown below. The compiler discard 50% ofthe ALU instruction although it cannot reduce, store branches,close, load, compute for the unoptimized CPI.
Write an equation relating the donor-atom concentration, the acceptor-atom concentration, the free-electron concentration, and the hole concentration for a doped semiconductor.
The signal noise ratio in an FM system is 4:1 The maximum allowed deviation is 4 KHz. How much frequency deviation is introduced by the phase shift caused by the noise when the modulating frequency is 650 Hz
Activation of a switch at t = 0 in a certain caused the voltage across a 20-mH inductor to exhibit the voltage response V(t) =4e-0.2t mV ( for t ≥ 0) determine i(t) for t ≥ o given that the energy stored in the inductor at t = ∞ is 0.64 mJ.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd