Problem a tension link shown to the right is used in

Assignment Help Mechanical Engineering
Reference no: EM13371277

Problem:

A tension link shown to the right is used in earth-moving equipment and is subjected to cyclic stresses varying from 10 ksi to 35 ksi. The link contains an internal crack that is 4 in long. If the link is made from A517 steel (σys=110 ksi and Kic= 170 ksi.in1/2), do the following:

a) Determine the factor of safety against net section yield in the presence of the crack.

b) Determine the factor of safety against brittle fracture for the same conditions.

c) If the maximum stress were increased (due to an accidental overload), which would occur first, net section yield or brittle fracture? Explain.

d) For Paris law coefficient of C=0.66 x 10-8 and n = 2.25, where stress is measured in ksi and crack growth in inches, estimate the number of cycles needed to grow the crack by the amount of 0.1 in.

e) If you were the engineer responsible for analyzing the life of this part, what would be your recommendation for continued service of this part (e.g. stopping using it immediately, repair or continue using it until next inspection, etc.)? Justify your decision based on sound engineering principles.

55_Determine factor of safety against brittle fracture.png

Reference no: EM13371277

Questions Cloud

Corporate enterpreneurshipinfusing new and innovative ideas : corporate enterpreneurshipinfusing new and innovative ideas into existing products and services although the
Airphone inc manufactures cellular telephones at a : q1. airphone inc. manufactures cellular telephones at a processing cost of 47 per unit.nbsp the company produces an
Marketing plandevelop a marketing plan for a new specialty : marketing plandevelop a marketing plan for a new specialty bariatric facility that will operate in the orlando
Problem a 5x5 plate with a crack size of 2a15 is under a : problem a 5x5 plate with a crack size of 2a1.5 is under a spectrum load as shown below. the plate has a yield strength
Problem a tension link shown to the right is used in : problem a tension link shown to the right is used in earth-moving equipment and is subjected to cyclic stresses varying
A large plate contains a central crack of length 2 mm and : a large plate contains a central crack of length 2 mm and is subjected to a cyclic stress normal to the crack which
Overvieweach student will create a detailed unified : overvieweach student will create a detailed unified technical design of network services given the scenario. prepare
After a long courtship andy and wendy chung were married on : after a long courtship andy and wendy chung were married on march 18 2013. this was a second marriage for both. andy
Question 1 consider the images distributed or collected as : question 1 consider the images distributed or collected as a part of your project. develop the equivalent of a low pass

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd