Problem 1a steel simple beam ab is supported by a copper

Assignment Help Mechanical Engineering
Reference no: EM13372355

Problem 1:

A steel simple beam AB is supported by a copper wire at the middle point C. The beam is subjected to a pair of concentrated force P = 4 KN (see figure)

steel beam AB: Lenght L = 4m with a fretangular cross section of height 20 cm x width 10 cm.

copper wire BD: lenght h = 1m with a circular cross section of diameter d = 5 mm.

Steel Es = 200 GPa; copper Ec = 100 GPa

Is this system determinate or indeterminate?

Determine the deflection δc of the beam at the end B.

2098_Determine the deflection.png

Problem 2:

A rigid bar (ignore its weight) hangs from flute equally spaced vertical wires (length L = 150 mm, spacing a = 50mm): two the steel and one of aluminum. The wires also support a load P acting on the bar. the diameter of the steel wires is da = 4 mm. Assume Es = 210 GPa and Ea = 70 GPa.

What load Pallow can be supported at the midpoint of the bar if the yield stress in the steel wires is 220 MPa and in the aluminium wire is 80 MPa? A saftey factor of n = 2 is needed.

443_Determine the deflection1.png

Reference no: EM13372355

Questions Cloud

Taskchoose one of the media articles or case : taskchoose one of the media articles or case studies.use the title of the articlecase study provided in
Write functions which solve each of the following problems : write functions which solve each of the following problems. you must place all of your functions in one project. if you
The international space station iss the mass is : the international space station iss the mass is approximately 990000 pounds orbits the earth at an altitude of
Critical review of a current debate in project managementto : critical review of a current debate in project managementto preparebullselect a current debate in project management
Problem 1a steel simple beam ab is supported by a copper : problem 1a steel simple beam ab is supported by a copper wire at the middle point c. the beam is subjected to a pair of
1 ace and baumont corporations make and sell electrical : 1. ace and baumont corporations make and sell electrical equipment. both have to decide whether or not to discount. the
Matrix1 : matrix1
1 formulate a field work research project and design : 1. formulate a field work research project and design research instruments such as questionnaires and interview
Ben grimm is a 40 partner in we four llc a super-heroing : ben grimm is a 40 partner in we four llc a super-heroing organization. he does most of the heavy lifting. reed has 40

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd