Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Project title - Planning & design of precast/prefabrication factory for structural member
You need to make a latch rive for given title about 18 pages with line spacing 1.5 including
1- study of structural member
2- study of pre cast structural member
3- study of plan & design of slimier of this factory
Verified Expert
This is an assignment is about civil engg. The concept of precast structures is also known as prefabricated or modular structures. The required structural components are first produced and then standardized in plants which are far away location from the building site, then brings to the site for assembly by transport. These structural components are manufactured by industrial mass production methods. The use of prefabricated and pre-assembled system is doubled in last 15 years. Approximately it is increased by 86%. This procedure reduces the waste generation during the construction. It also reduces adverse environmental impact on sites and amount of site labor. Whereas increases the quality of concreting work and worker safety.
dear sir i have project with title (planning & design of precast/prefabrication factory for structural member ) i wont u to make for me a literature review for this title about 18 pages with line spacing 1.5 ,picture and reference in this 18 pages i need this : 1- study of building structural member 2- study of precast/prefabrication structural member 3- study of plan & design of slimier of this factory i dont have any study for it , because all this topic is about building precast/prefabrication factory for structural member so i wont literature review for this topic (planning & design of precast/prefabrication factory for structural member ) and i Manichean what i wont in this 18 pages which is : 1- study or general information of building structural member 2- study or general information precast/prefabrication structural member 3- plan & design of precast/prefabrication factory slimier of this factory
dear sir i have project with title (planning & design of precast/prefabrication factory for structural member ) i wont u to make for me a latch rive for this title about 18 pages with line spacing 1.5 including 1- study of structural member 2- study of pre cast structural member 3- study of plan & design of slimier of this factory
A 23-lb crate is pushed by a force F, which has the magnitude that varies as shown on the graph. If the crate is originally at rest and it takes 3 seconds after applying the force to hit the bumper
Car B is driving straight toward the point O at a constant speed v. An observer, located at A, tracts the car with a radar gun. What is the speed |r(dot)B/A| that the observer at A records
The solids in a specimen have a specific gravity of 2.65. If the oven-dry mass of the specimen is 25kg, what is the volume of the solids in it
determine the required minimum diameter d of the post to the nearest 1/8 in. so that it will not yield when it is struck by the block.
if you were asked to determine the mechanical properties of ametal by concucting a test, what type of test whould you use, and what data can you abtain from that test
A cyclone separator is being used to remove particulates from a gas stream. The current removal efficiency is 96% for an air flow rate through the separator equal to 18 m3/s. Due to a process change, the air flow rate is expected to increase to 22 m3..
A rod of steel is 20 m long at a temperature of 200C. find the free expansion of the rod when the temperature is raised to 65 0 C. Find the temperature stress produced
Calculate how many chlorine atoms will be in an average neoprene chain? b) Sketch the bonding between polychloroprene chains due to sulfur linkages as neoprene is vulcanized into an elastomer. c) You decide to go swimming in Bear Lake in late Novembe..
A cut for a highway is shown in Figure P16.4. Determine the factor of safety of the slope using an ESA and a TSA. Assume a center of rotation, O, such that the slip surface passes through the toe of the slope.
If the tensil testing machine can apply no more than 925 lbs. of force to the specimen, calculate the maximum rod diameter that should be used. (precision 0.000)?
If log KSO, calcite (CaCO3(s)) = -8.61 at 50 oC, would calcite be over- or under- saturated in a hot water heater at 50 oC if the water was in equilibrium with calcite at 25 oC (log KSO = -8.30) when it entered the house
Using EES (or other) software and the relations given in Table A-33, generate the one dimensional normal shock functions by varying the upstream Mach number from 1 to 10 in increments of 0.5 for air with k =1.4.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd