Possible candidates for application

Assignment Help Mechanical Engineering
Reference no: EM13948285

A tubular shaft similar to that shown in Fig- ure 16.11 is to be designed that has an out- side diameter of 100 mm (4 in.) and a length of 1.25 m (4.1 ft). The mechanical charac- teristic of prime importance is bending stiff- ness in terms of the longitudinal modulus of elasticity. Stiffness is to be specified as maximum allowable deflection in bending; when subjected to three-point bending as in Figure 12.32, a load of 1700 N (380 lbf) is to produce an elastic deflection of no more than 0.20 mm (0.008 in.) at the midpoint position.

Continuous fibers that are oriented parallel to the tube axis will be used; possible fiber materials are glass, and carbon in standard-, intermediate-, and high-modulus grades. The matrix material is to be an epoxy resin, and fiber volume fraction is 0.40.

(a) Decide which of the four fiber materi- als are possible candidates for this application, and for each candidate determine the required inside diameter consistent with the above criteria.

(b) For each candidate, determine the re- quired cost, and on this basis, specify the fiber that would be the least expensive to use. Elastic modulus, density, and cost data for the fiber and matrix materials are con- tained in Table 16.6.

Reference no: EM13948285

Questions Cloud

Compute the corrosion penetration rate : Using the results of Problem 17.13, compute the  corrosion  penetration  rate,  in  mpy,  for the corrosion of iron in HCl (to form Fe2 + ions)   if   the   corrosion   current   density   is 8 X 10-5  A/cm2.
Create a formula to have excel compute annual savings : You do not need to put in personal information or actual values if you do not wish, but you must include some data for each of the various categories and income and expense line items.
Possible oxidation and reduction half-reactions : 1. (a) Write the possible oxidation and reduction half-reactions that occur when magnesium is immersed in each of the following solutions: (i) HCl, (ii) an HCl solution containing dissolved oxygen, (iii) an HCl solution containing dissolved oxygen..
What are the primary core american values : What are the primary core American values that this campaign is attempting to tap into. What values and aspirations does this campaign tap into relating to the subgroups of professional women and professional African American women
Possible candidates for application : Decide which of the four fiber materi- als are possible candidates for this application, and for each candidate determine the required inside diameter consistent with the above criteria.
Effective transfer rate from the server to the workstation : what is the effective transfer rate from the server to the workstation?
The press conference as critical incident : However skillful we are with framing, at times we are apt to go "off message." That is, under stress and in times of crisis, we may fail to communicate our best thoughts, self-image or regard for others.
What web-based sites offer file sharing similar to napster : What other Web-based sites offer file sharing similar to Napster?
What is the probability that this test makes a type ii error : Use the applet to calculate the power of the test against the alternative u = 122. Can the test be relied on to detect a mean that differs from 128 by 6?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the load on the prop

A horizontal cantilever of length L supports a load W, uniformly distributed along its length. the cantilever is proped to the level of the fixed end at a distance 3/4 L from that end. Determine the load on the prop.

  Assume the elastic modulus of rubber is 10-3 gpa and that

a catapult has two rubber bands each rubber band has a rectangular cross-section with a width 8 mm and thickness of 2

  What is the temperature at the center

Fireclay brick of dimensions 0.06 m x 0.09 m x 0.20 m is removed from a kiln at 1600 K and cooled in air at 40oC with h=50 W/m2/K. What is the temperature at the center and at the corners of the brick after 50 minutes of cooling?

  Steam turbine is operating at a steady state with mass flow

A steam turbine is operating at a steady state with a mass flow rate of 3682 kg/h at the inlet. The power output of the turbine is 8700 kW. Steam enters the turbine at a pressure of 40 bar, temperature of 320 oC, and with a velocity of 13 m/s. The ex..

  The inefficiencies of engine components determine the force

consider an aircraft powered by a turbojet engine that has a pressure ratio of 9. the aircraft is stationary on the

  The tank contains water to a depth of 5ft plus a depth of

an open rectangular tank is 6ft wide and 12ft long. the tank contains water to a depth of 5ft plus a depth of 2.5ft of

  Draw a sketch to represent the stress distribution

Calculate the magnitude of the moment acting at the build-in end and specify the orientation of the moment vector relative to the principal centroidal axes of the section with the aid of a sketch and determine the stresses at each corner of the bu..

  Direct tension-direct compression and column buckling

Describe when each type of failure occurs: direct tension, direct compression, column buckling, direct shear, torsional shear stress, bending stress

  One gallon is a volume measure of 231 in3 determine the

1. convert 8720 gallons per minute to ft3sec.2. one gallon is a volume measure of 231 in3. determine the velocity in a

  The amount of heat transfer during the whole process

1.5 kg of air in a piston/cylinder assembly has initial temperature and pressure 27oC and 1.5 bar respectively. Then the system is heated in constant volume to 727oC (state 1-2) and then heated again constant pressure to 1227oC (state 2-3).Determine ..

  Determine the electrical power

The exposed surfaces of the aluminum plate are painted with a very thin coating of high emissivity (s = 0.95) paint. Determine the electrical power that must be supplied to the heater to sustain the plate at a temperature of Ts = 35°C. How much of..

  Get rid of the brackets as much as possible

Simplify the following terms and get rid of the brackets as much as possible. All matrices in the equations below are square 3x3 matrices, [alpha] is a scalar, and Q is an orthogonal matrix.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd