Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A plate, 10 cm wide, 12 cm high and 1 cm thick, has a centrally located hole of 2 cm radius. The plate is subjected to a nominal (far-field) cyclic tensile stress of 100 MPa at R = 0. Two mode I fatigue cracks nucleate at the edges of the hole (as shown in Fig. 15.9) and propagate at a rate da/ dN = C(?K)3 , where C has a magnitude of 10-11 when da/dN is in units of m/cycle and AK is expressed in units of MPa.
(a) What is the transition crack size, lt, below which the growth of the fatigue crack is affected by the elastic strain field of the notch?
Assume small-scale yielding conditions at the tip of the fatigue crack and neglect the possibility of plastic deformation in the vicinity of the hole.
(b) If the crack initiates during the first stress cycle, calculate the number of fatigue cycles necessary to propagate the crack a distance of 1.5 cm on either side of the circular hole.
Compute the effective composite modulus of subgrade reaction (please consider the subbase, the presence of a relatively shallow rock foundation, and the potential loss of support)
Determine the peak outflow rate when the inflow hydrograph is routed through this basin and what is the design storage and water surface elevation at the peak outflow rate.
A batch system is assumed to be first order. The initial concentration is 225 mg/L. If the reaction rate constant is 0.65 hr^-1, how long will it take for the concentration to be one-quarter the starting concentration?
A trapezoidal channel is carrying water at a normal depth of 5.2 ft, the channel has a bottom width of 10 ft and side slopes of 2 H to 1 V. It is running on a slope of 0.005 ft/ft. What will be the shear stress in lb/ft^2 exerted on the channel be..
At a certain location on the surface of an engineering component, the material is in a state of plane stress with principal stresses of fmax = 150 MPa and fmin = 50 MPa (both tensile). If the yield strength of the material is Y = 350 MPa
Determine the maximum displacement of the plate A if the billet strikes the plate with a speed of 8 . Neglect the mass of the springs, rollers and the plates A and B. Take = 4000 , = 40000 .
If the compression process is isentropic, determine the required work input for this compression process, in kJ/kg of mixture.
A sanitary sewer with a 450 mm diameter is constructed on the minimum allowable slope of 0.9 m/km. What is the full capacity of the sewer? At what depths of flow in the pipe are the velocities of flow equal to 0.6 m/s. Assume Mannings constant n = 0...
A trapezoidal channel has a bottom width of 5 feet, a slideslope (horizontal:vertical) of 2, and a depth of flow of 4 feet. The elevation of the channel bottom drops 2 feet every 1000 feet of horizontal distance traveled. The discharge in the channel..
John Brooks a recent ME graduate from Central Michigan, bought an SUV for $30,000 with a down payment of $10,000. John had a little business on the side and did not have a girlfriend when he was at school and ehnce he was able to save the $10,000 for..
Estimate the total cost and cost per linear foot for furnushing and driving steel-sheet piling for construction of the basement of a building, 150 by 240 ft. the piles will be 22 in. wide, 18 ft. long, and weigh 40.3 Ib/Lin ft. the piles will be driv..
The theodolite's optical center is 4.66 ft above the upper baseline station at 110+71.25. a) What is the stationing chainage of the lower station
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd