Point b is 10 m above point a and the pressure at b must be

Assignment Help Mechanical Engineering
Reference no: EM13640913

Water at 40 degrees Celsius flows from A to B through a 300-mm cast iron pipe (ξ=0.000061 m), 250 m long. Point B is 10 m above point A, and the pressure at B must be maintained at 150 kPa. If the flow rate is 0.3 cubic meters per second, and the elevation of A is zero, what must be the pressure at A?

Reference no: EM13640913

Questions Cloud

What is the net heat flux from the surface when solar : in space ships heat rejection to the surroundings is by radiation. a radiator in a space ship has an absorptivity alpha
Suppose that the proportion of fatal single-car accidents : suppose that the proportion of fatal single-car accidents that involve alcohol consumption on the part of the drive is
What is the probability that the space vehicle will have a : a what is the probability that the space vehicle will have a successful launch?b given that the space vehicle had a
How much higher or lower is the launch point relative to : a projectile is fired with an initial speed of 34.0 ms at an angle of 35.0circ above the horizontal. the object hits
Point b is 10 m above point a and the pressure at b must be : water at 40 degrees celsius flows from a to b through a 300-mm cast iron pipe xi0.000061 m 250 m long. point b is 10 m
A student titrates 50ml apple juice and reports the : a student titrates 50ml apple juice and reports the following inthe titration to the phenolphthalein end point with
We can understand how pressure in water depends on depth by : we can understand how pressure in water depends on depth by considering a stack of bricks. for a stack of bricks the
Suppose that the average weekly earnings for employees in : suppose that the average weekly earnings for employees in general automotive repair shops is 450 and that the standard
Two gases are contained in gas bulbs connected by a valve : two gases are contained in gas bulbs connected by a valve. gas a ispresent in a 45 l bulb at a pressure of 388 torr.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the ratio of work delivered by the turbine to the

consider a steam power plant that operates between the pressure limits of 10 mpa and 20 kpa. steam enters the pump as

  A power plant operates a regenerative rankine cycle

A power plant operates a regenerative Rankine cycle with a reheat, one closed and one open feedwater heater and has a net power output of 1.2 x 109 Btu/hr.

  Employing the ideal gas model for the gas determine the

an insulated cylinder is initially divided into halves by a frictionless thermally conducting piston. on one side of

  Calculate the maximum length of the tube which can support

a 1000 diameter steel tube with a .020 wall thickness supports a 350lb load in compression as shown. calculate the

  Say you have two lumps of copper one hot and the other

say you have two lumps of copper one hot and the other cold. what is the maximum work you could obtain by running a

  An isentropic steam turbine processes 5kgs of steam at 4mpa

an isentropic steam turbine processes 5kgs of steam at 4mpa. the majority of this steam is exhausted at 50kpa and 100

  The inlet of the bend is 50 cm above the exit neglecting

water flowing in a horizontal 30 cm diameter pipe at 5 ms and 300 kpa gage enters a 90o bend reducing section which

  The specific gravity of solids is 270 determine the

a soil sample has a total unit weight of 16.97 knm3 and a void ratio of 0.84. the specific gravity of solids is 2.70.

  A shell-and-tube heat exchanger consisting of one shell

a shell-and-tube heat exchanger consisting of one shell pass and two tube passes is used to transfer heat from an

  Assume no temperature change during the pumping and find

an air pump with a 4-in piston and a 12-in stroke compresses atmospheric air into a 5ft3 evacuated tank. assume no

  The pressure coefficient is 10 at a and -03 at b assume

a rugged instrument used frequently for monitoring gas velocity in smoke stacks consists of two open tubes oriented to

  Determine the constants in the hall-petch equation and find

the yield strength of mild steel with an average grain size of 0.05 mm is 20000 psi. the yield strength of the same

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd