Plot thrust vs time what is the velocity of the rocket at

Assignment Help Mechanical Engineering
Reference no: EM13633560

A rocket has an initial mass of 25,000 kg of which 20,000 kg is fuel and oxygen. It is propelled directly upward from ground level (initial velocity V0 = 0) by a rocket engine with a constant thrust of 400,000 N created by 1000kg/s of combustion products exiting the rocket nozzle at a constant velocity of 400 m/s. The combustion products are created solely by the fuel and oxygen onboard the rocket. What is the time to burnout (all onboard fuel and oxygen exhausted)? Plot thrust vs. time. What is the velocity of the rocket at 15, 20 and 30 seconds? Find the maximum altitude attained by the rocket. Ignore air friction.

A force balance on the rocket yields the ordinary differential equation

m(t)dVdt- b vd = -m(t)g , m(t) = m0 - b*t

where b = fuel/oxygen burn rate in kg/s, m0 = initial total rocket mass in kg, vd is the exit velocity of the burning fuel/oxygen mixture in m/s (thrust = b * vd in N), and g is the acceleration of gravity.

Reference no: EM13633560

Questions Cloud

What percent of the original kinetic energy of the bullet : a block of mass 4kg is suspended from a spring with spring constant 500nm. a bullet weighing 50.0 g is fired into the
Heat input of 663 kj occurs in every cycle consider : a six-cylinder four-stroke internal combustion engine with compression ratio of 17 and displacement volume of 4.5 l is
A bell ringer decides to use a bowling ball to ring the : a bell ringer decides to use a bowling ball to ring the bell. he hangs the 7.3kg ball from the end of a 2m long rope.
A object is located 90 cm in front of a converging lens f : an object is located 9.0 cm in front of a converging lens f 6.0cm. determine a distance of the image and b the height
Plot thrust vs time what is the velocity of the rocket at : a rocket has an initial mass of 25000 kg of which 20000 kg is fuel and oxygen. it is propelled directly upward from
Name two ways to increase the statistical power of an : name two ways to increase the statistical power of an experiment. explain how each increases the probability of
If the temperature coefficient of expansion for brass is 19 : at 25oc an aluminum ring has an inner diameter of 4 cm and a brass rod has a diameter of 4.01 cm. if the temperature
Assume that as a newspaper reporter you must graph data : assume that as a newspaper reporter you must graph data showing that increased smoking causes an increased risk of lung
Determine the rate of entropy production kwk within the : a compressor used to deliver 2.10 kgmin of high pressure air requires 8.087 kw to operate. at the compressor inlet the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd