Plot the tensions in wires 1 and 2

Assignment Help Civil Engineering
Reference no: EM131037329

The 2-kg slider fits loosely in the smooth slot of the disk, which rotates about a vertical axis through point O. The slider is free to move slightly along the slot before one of the wires becomes taut. If the disk starts from rest at time t = 0 and has a constant clockwise angular acceleration of 0.5 red/s2 plot the tensions in wires 1 and 2 and the magnitude N of the force normal to the slot as functions of time t for the interval ≤ t ≤ 5 s.

1892_df77b91f-eece-4809-bf79-344bdeca499a.png

Reference no: EM131037329

Questions Cloud

Complete a risk assessment to identify potential threats : Threat Management and Disaster Recovery Final Paper. Using the NIST Special Publication 800-30, complete a Risk Assessment to identify potential threats for which a matching vulnerability exists in the above described environment
Compare with the case of static equilibrium in same position : compare with the case of static equilibrium in the same position.
Compare p with the minimum gripping force ps : Compare P with the minimum gripping force Ps required to hold the sphere in static equilibrium in the 30° position.
The current-mirror-loaded differential amplifier : 9.112 For the current-mirror-loaded differential amplifier inFig. P9.112, find: (a) differential input resistance, Rid (b) Ad (c) CMRR Assume β = 100, |VBE | = 0.7 V, |VA | = 60 V, Vt = 0.7 V, and kΩ (W/L) = 2 mA/V2.
Plot the tensions in wires 1 and 2 : plot the tensions in wires 1 and 2 and the magnitude N of the force normal to the slot as functions of time t for the interval ≤ t ≤ 5 s.
Calculate the uppi for both prices : Suppose that firms 1 and 2 sell widgets and are planning to merge. They each charge $100 per widget and each has a marginal cost of $80 per widget. Assuming that the cost reductions are cognizable, calculate the UPPI for both prices
For the current-mirror-loaded differential pair : 9.111 For the current-mirror-loaded differential pair in Fig. P9.111, find: (a) differential input resistance, Rid (b) Ad (c) CMRR Assume β = 100, |VBE | = 0.7 V, and |VA | = 60 V.
Calculate the force exerted by the seat on the 90-kg pilot : A pilot flies an airplane at a constant speed of 600 km/h in the vertical circle of radius 1000 m. Calculate the force exerted by the seat on the 90-kg pilot at point A and at point B.
What is a commonly accepted definition of miracle : What is a commonly accepted definition of "miracle"? The philosopher David Hume is well known for his opposition to miracles. What are two or three of Hume's objections to miracles?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Estimate the ground- level concentration at a distance

A point source with effective stack height of 50 m emits 80 g/s of on a clear summer day with surface winds at 4 m/s. Winds at 50 m are 5 m/s. An inversion layer starts at an elevation of 250 m.

  Determine what would be the flow rate in gpm

Suppose that a water treatment plant has a Parshall Flume with a 4 ft wide throat. a) If the upstream depth of the water (ha) is 1 ft and the depth of the water in the throat section (hb) is 0.65 ft, what is the flow rate in gpm

  Determine the maximum acceleration from rest

A rear-wheel-drive car 2600 lb, has an 80-inch wheelbase, a center of gravity 20 inches above the road surface and 30 inches behind the front axle, a drivetrain efficiency of 85%, 14-inch-radius wheels,

  How many holes are required to break

Conduct a powder factor design for the following conditions: -Rock is iron ore; density is 5370 lb/cubic yards -Rock swells 60% from in situ when broken -Bench height is 45ft -Drill hole diameter is 12.25 inches

  Tabulate the natural log of the equilibrium constant

Compare your results to those obtained by combining the ln KP values for the two equilibrium reactions CO2 = CO + O2 and H2O = H2 +O2 given in Table A-28. 0031

  Is this stress tension or compression

If the rod is snugly fitted against two immovablenonconducting walls at a temperature of 15oC and thenheated uniformly to at 115oC, what is its length at115oC? If the modulus of elasticity of steel is 207 GPa,what is the stress induced in the bar? Is..

  Determine the shear-thrust and moment in the arch at point c

The three hinged arch is composed of segments of a circle. Support points A and D are not at the same level.Determine: (a) the horizontal and vertical components of reaction at A and D.

  Determine x and z components of force required to hold

The stream hts a stationary splitter, such that half of the flow is diverted upward at 45o. and the other half is directed downward, and both streams have a final speed of 18ft/s.

  Design coagulation-flocculation and sedimentation

What effect does removing 70-100 sieve fraction have on the head-loss characteristics and on the depth of expanded bed and Comment on the differences and likely reasons for the differences.

  Calculate the mass flux rate and the flow rate

Water is flowing in a 6-cm diameter pipe at 20 m/s at 10?C. If the pipe enlarges to a diameter of 12-cm, calculate the reduced velocity. Also, calculate the mass flux rate and the flow rate.

  Calculate steady state concentration of organic n into lake

Colette Lake has a surface area of 103 ha and a mean depth of 8 m. The pH of the water is 7.6. The lake receives surface water from a lake upstream, rainfall, and diffuse groundwater input. Atmospheric inorganic N deposition is insignificant.

  Determine the normal depth in the channel for a discharge

If you have 10 kips acting downward on a foundation and footing, 4 feet long, with uniformly distributed load acting up ward of 2.5 k/ft (soil) also 4 ft long. what are the reactions, shear forces, and bending moments at the tree critical points?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd