Plot the temperature distribution for the entire strip

Assignment Help Mechanical Engineering
Reference no: EM131086794

The temperature of a flowing gas is to be measured with

a) thermocouple junction and wire stretched between two legs of a sting, a wind tunnel test fixture. The junc- tion is formed by butt-welding two wires of different material, as shown in the schematic. For wires of diame- ter D = 125 µ,m and a convection coefficient of h = 700 W/m2 · K, determine the minimum separation
film (-w1/2 x +w1/2).

(b) If the heat flux provided by the laser is 10,000 W/m2, determine the temperature of the plastic film at the center (x = 0) and its edges (x = ±w1/2).

(c) Plot the temperature distribution for the entire strip and point out its special features.

Reference no: EM131086794

Questions Cloud

Identify ethical and regulatory considerations : Identify ethical and regulatory considerations. Analyze the following factors that have affected the coffee industry over time: Explain the effects of supply and demand generally and specifically related to the coffee industry.
Large portion of refining and pipeline capacity : "Hurricane Katrina damaged a large portion of refining and pipeline capacity when it swept through the Gulf coast states in August 2005. As a result of this, many gasoline distributors were not able to maintain normal deliveries. At the pre-hurric..
Calculate the wages of two workers : therewere 500 workers in a factory. Their mean weight was calculated as Rs200. Later on it was discovered that the wages of 2 workers were missread as 180 and 20 in place of 80 to 220. Find the correct average?
Discuss why penicillin was called the miracle drug : Discuss why Penicillin was called the miracle drug when it was first used in the 1940's.
Plot the temperature distribution for the entire strip : Plot the temperature distribution for the entire strip
Discuss different type of promotion use by several companies : Discuss different types of promotions used by several companies. Explain group promotion mix components by company and analyze them for a consistent message. Identify the likely target market for each piece of promotion.
Write down an expression for the population in year : ECON131 - Quantitative Methods in Economics, Business and Finance - Write down an expression for the population in year
Dividing the amount of interest : (a) Based on dividing the amount of interest equally between the first and second halves of the year, state the rate of interest for a 6-month period (simple interest method).
Find the total side trust given by the liquids : Find the total side trust given by the liquids on the vertical plate.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd