Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The Seebeck voltage (?) to relative temperature (T) conversion for a copper-constantan thermocouple with an ice point (0.00°C) reference is given over the range -160.°C to 400.°C by T = a0 a1? + a2?2 + a3?3 + ... + a7?7 , where T is in °C and ? is the Seebeck voltage in microvolts (i.e., 10-6 V). The polynomial coefficients given by the National Bureau of Standards are
a0 = 0.100860910
a1 = 25727.94369
a2 = -767345.8295
a3 = 78025595.81
a4 = -9247486589
a5 = 6.97688 × 1011
a6 = -2.66192 × 1013
a7 = 3.94078 × 1014
a. Write an interactive computer program that asks the user for the thermocouple voltage (in the proper units) and returns the temperature, Seebeck, Peltier, and difference in Kelvin coefficients (in proper units) to the screen.
b. Plot the Seebeck voltage and the Seebeck and Peltier coefficients vs. temperature over the temperature range of 100.°C to 400.°C using at least 100 points per curve.
question 1the linear circuit shown above consists of dependent sources and resistors only. if the value of the voltage
The sampling frequency in a DSP system is fs=8 kHz. Anti-aliasing filter used in the system is the second-order Butterworth filter with cutoff frequency of fc=3.4 kHz. What is the percentage of aliasing level at the frequency f=2.5 kHz
The two holes in the part have already been drilled and will the used for clamping the part during origin, Write the part program in the word address format with TAB separation and variable word order,
Given: A permanent magnet DC motor with kv = 0.7 v-s is tested under the following two conditions: Test 1: Apply 120 V; motor unloaded, Ia=2A and w=160 rad/s Test 2: Apply 120 V, increase load torque until Ia=6A and w=137.1 rad/s
You measure 0 V across the diode of Fig. 3-23a. Next you check the source voltage and it reads +5 V with respect to ground. What is wrong with the circuit?
Design a majority of 1s circuit such that the output F is 1when a majority of the inputs X,Y,Z are 1. Simplify thefucion to its minimum form using karnaugh map.
A rectangular loop of wire containing a high resistance voltmeter has corners initially at (a/2, b/2, 0), (-a/2, b/2, 0), (-a/2, -b/2, 0) and (a/2,-b/2, 0). The loop begins to rotate about the x axis at constant angular velocity w.
Discuss why the primary of a power transformer would have excessive current if the secondary were short-circuited. Why would there be no voltage across the secondary if the primary is open
A 25 MVA, three phase, 13.5kV, Y-connected, two pole, 60 Hz synchronous generator was tested by the open circuit test and short circuit test and tabulated in table 1. If the armature resistance is 0.24 ohms per phase
Using verilog hardware descriptional language or vhdl create a non-expandable dataflow description of a 2-bit magnitude comparator, from that create a behavioral dataflow description to create an expandable 2-bit magnitude comparator
Three capacitors are found that each have an impedance of -j2.0, and they are connected in parallel with the load in a wye configuration. Determine the power factor of the combined load as seen by the source.
How do you create a C-style string. Give examples. How do you input or output a C-style string. What kinds of tools are available to work with C-style strings. Show some examples of using those tools.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd