Plot the mobility transfer functions magnitude

Assignment Help Mechanical Engineering
Reference no: EM131144031

From a compliance transfer function of a spring-mass-damper system the stiffness is determined to have a value of 0.5 N/m, a natural frequency of 0.25 rad/s, and a damping coefficient of 0.087 kg/s.

Plot the mobility transfer function's magnitude and phase for the system.

Reference no: EM131144031

Questions Cloud

Determine the response of an undamped system : Determine the response of an undamped system to a ramp input of the form F(t) = F0 t, where F0 is a constant.
How successful will she be at completing that goal : As her social worker, you might feel that going into drug and alcohol rehab is a priority. However, she might feel that keeping her job, and therefore getting a car, is much more of a priority. If you disregard her goals and instead refer her to a..
The volume of accounting instructions is already high : The volume of accounting instructions is already high. If things go on like this, where will we be in 20 or 30 years time?- Do you agree with this idea?
Plot the inertance transfer functions magnitude : Plot the inertance transfer function's magnitude and phase for this system.
Plot the mobility transfer functions magnitude : Plot the mobility transfer function's magnitude and phase for the system.
Which is true about the office of the president : Which of the following is a procedural tactic in which a minority of senators can block a bill by talking until other senators give in and the bill is withdrawn?
Determine a value of damping that causes the transient term : Determine a value of damping that causes the transient term to die out within 3 seconds. Try to find the smallest such value of damping remembering that added damping is usually expensive.
Plot the response for three periods for the case : Plot the response for three periods for the case m = 1 kg, k = 100 N/m, and F0 = 50 N
Why do you think this behaviorist approach is best : Describe how that behaviorist would teach an adult a new skill. Be specific; what is the skill? What steps would the behaviorist use? Would that behaviorist use a different approach with a child?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Exiting stream 3 is at 079 mpa and is know to contain a

high pressure steam steam 1 at a rate of 1000kgh initially at 3.5 mpa and 350 c is expanded in a turbine to obtain

  Bicycle floor pump has a cylindrical tube

A bicycle floor pump has a cylindrical tube with an inside diameter of 1.0 inches. On the pump's upstroke, a diaphragm check valve opens and brings air in at 13.0 psia. The air is then transferred to the tire during the down stroke. The stroke length..

  Discuss johnson & johnson''s approach on providing an it

Needing a writing help with a 3-4 page paper on the Case Study 6-2 Johnson & Johnson's Enterprise Architecture, this is from Managing and Using Information Systems by Pearson & Saunders.

  Water is being filled with water through two inlet pipes

A tank initially filled with 500 lb liquid water is being filled with water through two inlet pipes. One delivers hot water at mass flow rate of 1.5 lb/min and the second delivers cold water at a mass flow rate of 3 lb/min. A single exit pipe is drai..

  Plot the shear force and bending moment diagrams

Plot the shear force and bending moment diagrams and determine the maximum stress due to bending, the factor of safety in operation if the UTS of the material is 500 MPa, and the value radius of curvature between the suspension points.

  Determine the velocity of each car after all collisions

Knowing that the coefficient of restitution is 0.8 between B and C, and 0.5 between A and B, Determine the velocity of each car after all collisions have taken place.

  How it has been possible to simplify the optical systems

Describe how it has been possible to simplify the optical systems in more contemporary instruments.

  A heat pump with a cop of 30 is used to heat air contained

a heat pump with a cop of 3.0 is used to heat air contained in a 1205.4m3 of well-insulated rigid tank. initially the

  Tube side convection coefficient

(a) What are the gas and water outlet temperatures? (b) Assuming fully developed flow, what is the tube- side convection coefficient? (c) With all other conditions remaining the same, pl

  Draw a schematic of the system

(a) Draw a schematic of the system and (b) determine if the inventor's claims are true.

  Estimate the fugacity for each species

Estimate the fugacity for each species in the following gases at 290 K and 800 bar: (a) Pure oxygen; (b) Pure nitrogen; (c) Oxygen and nitrogen in a 30% mol O2 and 70% mol N2 mixture using the Lewis-Randall rule, and (d) Oxygen and nitrogen mixture i..

  Diffusion of carbon-what depth would the concentration

Diffusion of carbon into BCC iron for 12 hours at a temperature of 5000C results in a carbon concentration of 0.2 wt% at a depth 2 mm from the surface. At what depth would the concentration be 0.2 wt%, if the diffusion occurred for 6 hours at 8000C?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd