Plot the first order polynomial second order polynomian and

Assignment Help Mechanical Engineering
Reference no: EM13631218

Below is pressure measured at different time

Time (s)                 Pressure (psi)

1                                   26.1

2                                    27.0

3                                 28.2

4                                 29.0

5                                 29.8

6                                 30.6

7                                 31.1

8                                 31.3

9                                 31.0

10                               30.5

(1) Plot the first order polynomial second order polynomian and third order polynomia to these data. Plot both data points (with'o') and function line ('-') on the same plot. Keep the three plots on the same plot. (use subplot).

(2) Calculate the sum of squared residuals of each plot (J number). Also plot the residual of each plot. Based on the solution choose which polynomial is the best choice (1st, 2nd, or 3rd order)?

(3) Write down this polynomial.

Reference no: EM13631218

Questions Cloud

An rlc oscillator circuit contains a 630 ohm resistor and a : an rlc oscillator circuit contains a 63.0 ohm resistor and a 1.80-mh inductor. what capacitance is necessary for the
Estimate the spacing between the two irrandiance maxima : estimate the spacing between the two irrandiance maxima closest to the geometric of a plain wave illuminated
Light from a helium-neon laser wavelength633 nm is focused : light from a helium-neon laser wavelength633 nm is focused through a pinhole prior to illuminating a 1.00 mm diameter
A diesel engine develops 110 kw and uses 0245 kg of fuel : in a diesel engine compresses pure air in a cylinder so that the temperature of the air increases. just before the
Plot the first order polynomial second order polynomian and : below is pressure measured at different timetime
A photograph of this zone plate is to be reduced on : a fresnel zone plate is prepared with a drawing program and printed on a laser printer. the printed zone plate has a
A 50 w light bulb shines through two polarizers after : a 50 w light bulb shines through two polarizers. after having passed through the first polarizer the electric field
An ideal regenerative steam power cycle operates so that : an ideal regenerative steam power cycle operates so that steam enters the turbine at 30 bars and 500 degrees celcius
Find out the coefficients m and b of the function you : below is measured voltage v at different time stimes 0 0.5 1 1.5 2 2.5

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd