Plot the current waveforms on both sides of the converter

Assignment Help Electrical Engineering
Reference no: EM13272328

1- A switch-mode dc-dc converter is operating at a switching frequency of 20kHz, and Vd=150V. The average current being drawn by the dc motor is 8.0 A. In the equivalent circuit of the dc motor, Ea=100V, Ra=0.25 ohm, and La=4mH.
a). plot the output current and calculate the peak-to-peak ripple and
b). plot the dc-side current

2- the motor goes into regenerative braking mode. The average current being supplied by the motor to the converter during braking is 8.0A.
a). Plot the voltage and current waveforms on both sides of this converter.
b). Calculate the average power flow into the converter

if the motor is rotating in the reverse direction, with the same current draw and the same induced emf Ea value of the opposite polarity

Reference no: EM13272328

Questions Cloud

What is the schwarzchild radius of our galaxys black hole : The black hole at the center of the Milky way galaxy is estimated to contain about 4 million solar masses. (msun= 2 x 1030 kg), What is the Schwarzchild radius of our galaxy's black hole
Explain the so-called zinc blende crystal structure : Silicon Carbide (SiC) is a ceramic material with the so-called zinc blende crystal structure. It can be constructed from the FCC unit cell using a two-atom basis consisting of a Si atom at (0,0,0) and a C atom at (¼, ¼ , ¼).
Write the lagrangian for the system : Two pendula of equal length b and equal masses m connected by a spring of force constant k. Write the Lagrangian for the system, and use it to derive the equations of motion of the system
How might pam and josh use mutual funds : Finally, they talk with various financial advisers and other investors to gather additional information.
Plot the current waveforms on both sides of the converter : A switch-mode dc-dc converter is operating at a switching frequency of 20kHz, and Vd=150V. The average current being drawn by the dc motor is 8.0 A. In the equivalent circuit of the dc motor, Ea=100V, Ra=0.25 ohm, and La=4mH.
Explain what is the partition coefficient of the compound : A 20 mg sample of a compound is dissolved in 5.0 ml of water and extracted with 2.5 mL of heptane.After separation of the layers, the heptane layer is found to contain 15 mg of the compound. What is the partition coefficient of the compound, Khept..
What is the incremental savings of buying the valves : The equipment cannot be used elsewhere in the company, and it has no market value. However, the space occupied by the production of the valve can be used by another production group that is currently leasing space for $55,000 per year.
What is the rms current operating at its resonance frequency : a series RLC circuit contains a resistor of 20 ohms, a capacitor of 0.75 mF and an inductor of 120mH, what is the rms current operating at its resonance freq.
Explain dcm/bicarbonate systems were different : If the partition coefficients for the DCM/water and DCM/bicarbonate systems were different, what was the reason

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Define transmit power

The signal to noise ratio at the receiver is required to be at least 17 dB. The average noise power at the receiver is 1 mW. The cable loss between the transmitter and the receiver is 2.5 dB/km

  Calculate the maximum allowable gate drive power

A thyristor is triggered by a pulse of train of 5kHz.The duty ratio of the pulse train are 0.5. If allowable average gate power is 100W, calculate the maximum allowable gate drive power.

  What is done in airplane in flight to mitigate complications

A flashlight battery with a voltage of 1.2 would be considered. During servicing, Ni-Cad batteries are normally overcharged to of the rated amp-hour capacity. What is done in an airplane in flight to mitigate this complication

  Find the magnetic field produced by the two filaments

Two strands of infinitely long current rights carry currents of equal magnitude. Find the magnetic field produced by the two filaments at the midpoint between the two strands. Compare this result if the currents: a) have the same direction

  Write formulas of the compounds and an arrow followed by nr

You mix aqueous solutions of sodium iodide and lead(II) acetate. If a reaction occurs, write the balanced molecular equation and the net ionic equation. If no reaction occurs, indicate this by writing the formulas of the compounds and an arrow fol..

  Determine if system is stable-marginal stable or unstable

Consider a system equation s^4 + s^3 + s^2 + 2s + 10 = 0. FInd out its Routh Table. Determine if this system is stable, marginal stable or unstable. How many roots are stable and how many roots are unstable.

  Find exponential fourier series coeffecients of functions

Determine the periods and find exponential fourier series coeffecients of functions. A.) f(t) = 2(cost)(cos2t) B.) g(t) = 3 + 2e^-j2t + 2e^j2t + 2cos4t C.) h(t) = 4

  What is the rms value of the current through the capacitor

a 10uF capacitor is plugged into a 110v rms 60 hz voltage source with an ammeter in series. what is the rms value of the current through the capacitor?

  What is the value of the feedback resistor required

A temperature sensor covers a range of 0 to 70 degrees C with an output sensitivity of 2 mV/degree C. The sensor is input to an ADC with voltage range of 0 to 4V. What is the value of the feedback resistor required for an inverting amplifier circu..

  What is the value of the total circuit complex impedance

An input signal of 10V at 0o and a frequency of 1592 Hz is applied to a series RLC circuit with resistor R = 1000 ohm, inductor L = 0.2 H, and capacitor C = 0.1 F. what is The value of the total circuit complex impedance

  What is the feedback factor if a manufacturing error results

A negative feedback amplifier has a close-loop gain Af=100 and an open-loop gain A=105. What is the feedback factor If a manufacturing error results in a reduction of A to 103, what close-loop gain results

  What size of the counter we need in order to obtain signals

There is a 50 Mhz clock signal on the FPGA board. we want to have a 1 Hz signal for testing all the designs. Find out what size of the counter we need in order to obtain this signal from the on board clock.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd