Plot a mohr circle

Assignment Help Civil Engineering
Reference no: EM13534508

Plot a Mohr’s circle for the following stresseson a square soil element:

σx = 100kPa

σy = 200kPa

τxy = 20 kPa (forceis counterclockwise on the top horizontal surface of theelement)

Determine the following (either from the circle or from equations):

a. Principalstresses

b. Angle of the planeson which the principal stresses act

c. Shear and normal stresses on aplane that is 37 degrees from horizontal

Reference no: EM13534508

Questions Cloud

Fundamentals of hydraulic engineering : A stabilization pond is designed for a 35-day detention time. If the pond is maintained at a capacity of 40 acre-feet, what is theaverage gpd flow to the stabilizaiton pond?
Going from west to east on the same section of the road : A section of highway is 18 km long. A bus going fromeast to west on this road climbs for 6 minutes at one speed, levelsoff for 6 minutes at a second speed and descends for 6 minutes at athird speed. Going from west to east on the same section ofthe r..
How to design a simply supported rectangular concrete beam : How to design a simply supported rectangular concrete beam havingcross section of 20 mm by 40 mm and a length of 3 meters that couldcarry a uniform load of 1000 KN.
Which direction to apply the force components : When drawing a FBD, how do you know which direction the x, y and z components are applied? I know that the sum of forces in each direction and the moments about each axis have to equal zero so I know some FBD are pretty self explanatory
Plot a mohr circle : Shear and normal stresses on aplane that is 37 degrees from horizontal
Calculate its book value using straight-line depreciation : An asset costs $14 000 and has a scrap value of $3000 after sevenyears. Calculate its book value using straight-line depreciation
Calculate as many principal or maximum strains : The direct strain at an angle of 30o,to one of theprincipal axes was 1.34x10-3 and the corresponding shearstrain was 8.52x10-4. Calculate as many principal or maximum strains at the point
What is tanget distance : A 6 degree 30 minute who curve, whose degree is determine by a 100-ft chord , connect two tangent  that intersect at  an angle of 37 degree 18 minute calculate what is tanget distance?
What would be the capillary pressure between oil : Assume that the interfacial tension between oil-water is 22 dynes/cm and the contact angle through water is 93

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the velocity at which shuttle hits the player bs racket

In Singles badminton game, shuttle is smashed by Player A from close to base line, which is 6 m from the net. Height of the net to be cleared by a smash is 1.55 m. The shuttle is hit by player A at a speed of 250 km/h.

  What is the 2-4-6-trichlorophenol concentration in ppm

A 500 L (132 gal) tank contains 255 mg/L 2,4,6-trichlorophenol dissolved in trichloroethylene (TCE). What is the 2,4,6-trichlorophenol concentration in ppm Assume the temperature of the system is 20 degrees C.

  Find the gauge pressure at a second point in the line

At one point in a pipeline, the water's speed is 3.00 m/s and the gauge pressure is 4.00×10^4 Pa. Find the gauge pressure at a second point in the line 11.0 m lower than the first if the pipe diameter at the second point is twice that at the first..

  What is the minimum size of the reactor required for a plug

A minimum contact time of 30 min is required to reduce the pathogen concentration from 100 pathogens/L to below 1 pathogen/L through a first- order decay process. You plan on treating water at a rate of 1,000 gal/min.

  What is the distance-corrected for temperatures

A survey distance of 369.98 ft was recorded when the field temperatures was 100 degreesF. What is the distance, corrected for temperatures

  Determine the gage pressure in the water tank a

A manometer connects a large water tank open to the atmosphere to a closed spherical tank of air. The manometer contains both oil and water. Find the gage pressure in the tank "A".

  Calculate the time needed for the particles to set

For a temperature of 10 degree C, calculate the time needed for the following particles to settle 0.3m: a) a 20um mineral particle with a specific gravity of 2.1, and b) a 2 um organic particle with a specific gravity of 1.2

  What would be the new minimum downstream do

A single source of BOD causes an oxygen sag curve with a minimum downstream DO equal to 6.0 mg/L. If the BOD of the waste is doubled (without increasing the waste flow rate), what would be the new minimum downstream DO

  Using newton raphson method determine highest real root of f

determine the highest real root of f(x)= 0.95x^3 - 5.9x^2 +10.9x-6: (a)graphically. (b) using the newton raphson method(three iterations, xi= 3.5). (c) using the secant method(three iterations, xi-1= 2.5 and xi= 3.5).

  Determine the maximum bending stress on the outside surface

A concentrated moment is applied to the free end. Determine the maximum bending stress on the outside surface of the cylinder and the maximum bending stress on the inside surface of the cylinder.

  At what constant rate would train need to be decelerating

An excursion train, travelling at 80ft/s, encounters a rain shower. The point A lies directly 8ft. beneath the lip of an overhang in the observation car. The raindrops can be assumed to be falling at a constant speed of 40ft/s.

  Compute the percent voids in total mix and percent voids

An aggregate blend is composed of 59% coarse aggregate by weight (sp. Gr. 2.635), 35% fine aggregate (Sp. Gr. 2.710), and 5% filler (Sp. Gr. 2.748). The compacted specimen contains 6% asphalt binder

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd