Plot a calibration curve from these data

Assignment Help Mechanical Engineering
Reference no: EM131083550

A standard solution was put through appropriate dilutions to give the concentrations of iron shown below. The iron(II)-1,10,phenanthroline complex was then formed in 25.0·mL aliquots of these solutions, following which each was diluted to 50.0 mL. The following absorbances (1.00-cm cells) were recorded at 510 nm:

2249_a2103b7a-98e3-47f3-8ba8-19dbe41b9a6e.png

(a) Plot a calibration curve from these data.

(b) Use the method of least squares to find an equation relating absorbance and the concentration of iron(II).

(c) Calculate the standard deviation of the slope and intercept.

Reference no: EM131083550

Questions Cloud

Customers arrive at the veryfast bank as a poisson process : Continuing Problem 10.5.5, suppose each service time is either one minute or two minutes equiprobably, independent of the arrival process or the other service times What is the PMF of the number of customers N(t) in service at the bank at time t?
What is collusion : 1. What is collusion? How can collusion affect the bidding process? What can be done to counter it?
Socialist economic system-market economic system : China is currently a socialist economic system. In view of China's explosive growth in supplying goods to the world do you see China becoming more of a market economic system. Why/Why not?
Successful marketing communication campaign : Web-based technologies can be combined with traditional media to build a successful marketing communication campaign. Cite two specific examples of companies/brands using this combination approach and discuss what made these campaigns successful. ..
Plot a calibration curve from these data : Plot a calibration curve from these data.
Market interest rate constitute : Central bank adjustments of an interest rate on advances extended at an above-market interest rate constitute:
Statements is sequentially correct : Which of the following statements is sequentially correct?
Sum of two independent poisson processes : or a Poisson process of rate λ, the Bernoulli arrival approximation assumes that in any very small interval of length ?, there is either 0 arrivals with probability 1-λ? or 1 arrival with probability λ?. Use this approximation to prove Theorem 10..
Risk-averse person prefers gamble : Which of the following statements is TRUE? A risk-averse person prefers gamble B to gamble A. A risk-averse person prefers gamble A to gamble B. A risk-neutral person prefers gamble A to gamble B. A risk-neutral person prefers gamble B to gamble A.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate a the velocity at the instant the fuel burned out

a rocket is launched vertically upward. the fuel lasts 20 s and during this time the rocket has a uniform upward

  The automobile shown has 1200kg mass with center of gravity

the automobile shown has 1200kg mass with center of gravity at point g and all wheel have the same 0.34m radius if the

  Determine the total entropy generation

A piston/cylinder system contains superheated vapor initially at 400C and 600 kPa. The system is cooled at constant pressure by exchanging heat to the surroundings until the cylinder contains only saturated liquid. The surroundings are at 25C.

  How much energy was input to the motor to perform this task

a compressor raises the pressure of 3kg of air gamma 1.4 adiabatically from 100kpa 288k to 450kpa. the electric motor

  What is the effect on the critical load when the rods act

What is the effect on the critical load when the rods act as a single member?

  Find the current in antenna b when unit a transmits

Two units communicate with each other at 120 MHz and 10 W, in free space. Unit A uses a half-wavelength dipole antenna placed as shown in Figure. Unit B uses a 1/100 wavelength long dipole antenna and is 10 km from the transmitting antenna as show..

  Derive an equation calculating the efficiency of the power

a gasoline powergen consists of a gasoline engine designed to convert the chemical energy chee of gasoline to

  Determine the power required by the compressor and the rate

air with mass flow rate of 0.4 kgs enters an insulated compressor operating at steady state.determine the power

  Coefficient of friction at the tool and chip interface

A cutting tool (0.250in wide, rake angle 5 degrees) is used to machine in orthogonal mode. the depth of cut is 0.010in and the chip thickness is 0.027in. Calculate the shear angle and coefficient of friction at the tool and chip interface?

  If instead of being free the rod ends are fixed at room

for steel cp 135 jkg-k a 4.5x10-6 ok density 7.85 gcm3 e 207 gpaa. a 1 m long steel rod 10 cm in diameter is heated

  Determine the air exhaust velocity

Air is expanded isentropic ally in a horizontal nozzle from an initial pressure of 1.0 MPa, of a temperature of 800 K, to an exhaust pressure of 101 kPa. If the air enters the nozzle with a velocity of 100 m/s, determine the air exhaust velocity. Ass..

  A fan is to accelerate quiescent velocity is 0 ms air to a

assuming there are both a pressure gage and a manometer attached to a gas tank which has a pressure lower than patm. if

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd