Plains like texas need elevated tank to supply tap water

Assignment Help Mechanical Engineering
Reference no: EM13709644

Typical towns in states with big plains like Texas need an elevated tank to supply tap water. Below there is a picture of a typical elevated tank. If we approximate the tank as a cylinder with a diameter of 50 ft and a height of 25 ft, answer the following questions: Bernoulli s Equation (12 . 1) & Conservation of Mass (6 . 1) 3. Finally, estimate the time to empty it if the mean flow velocity at the discharge pipe is governed by the formula derived in part 2 (see below). Again, the discharge pipe has a 12 in. pipe diameter and the water level is initially at 250 ft above ground and the water level is initially at 250 ft above ground. Note: The elevated tank empties at 225 ft.

Reference no: EM13709644

Questions Cloud

Fluid speed exactly equal to the free-stream speed : Assuming ideal flow, use the method of separation of variables in polar coordinates to find the stream function for uniform flow at speed U? over a circular cylinder of radius R. At what points on the cylinder is the fluid speed exactly equal to the ..
In a certain electro chemical dissolution process of iron : In a certain electro chemical dissolution process of iron, a MRR of 2 cm3 /min was desired. Determine the amount of current required for the process. Assume current efficiency = 100%. Atomic Weight of Iron = 56 gm, Valence = 2, Density of Iron = 7.8 ..
Atomic weight of nickel and density of nickel : Calculate the specific removal rate and MRR (Volume of metal removed/sec) of Nickel in a certain electro chemical dissolution process, when a current of 500 A is being passed through the cell. Assume current efficiency = 100%. Atomic Weight of Nickel..
Explanation of ikea analysis report : Explain changes to the compensation and incentives at your company that are necessary to reinforce your recommendations and increase efforts for continuous improvement throughout IKEA
Plains like texas need elevated tank to supply tap water : Typical towns in states with big plains like Texas need an elevated tank to supply tap water. Below there is a picture of a typical elevated tank. If we approximate the tank as a cylinder with a diameter of 50 ft and a height of 25 ft, answer the fol..
Description of work cells in lean manufacturing : Explain how the cell concept works to improve productivity and quality, and how it acts as a means to support lean manufacturing.
Power plant is being developed to operate irrigation system : A Rankine cycle power plant is being developed to operate an irrigation system. In this power plant solar energy will be used to boil a low boiling point fluid within glazed flat plate solar collectors. The working fluid that has been selected is the..
Determine the air exhaust velocity : Air is expanded isentropic ally in a horizontal nozzle from an initial pressure of 1.0 MPa, of a temperature of 800 K, to an exhaust pressure of 101 kPa. If the air enters the nozzle with a velocity of 100 m/s, determine the air exhaust velocity. Ass..
Oxygen flow being expelled from the cylinder generate : A high-pressure oxygen cylinder, typically found in most welding shops, accidentally is knocked over and the valve on top of the cylinder breaks off. This creates a hole with a radius of 14 mm. Prior to the accident, the internal pressure of the oxyg..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd