Phase analysis and microstructure sketch

Assignment Help Electrical Engineering
Reference no: EM13866858

1. Perform a phase analysis and microstructure sketch for a 1035 plain carbon steel at (a) 723+oC, and (b) 723-oC. Show the lever rule calculation for one phase at each temperature.

3. Perform a phase analysis and microstructure sketch for a 1095 plain carbon steel at (a) 723+oC, and (b) 723-oC.  Show the lever rule calculation for one phase at each temperature.

4. Using your phase analysis from Problem 3, determine: (a) The weight percent of proeutectoid ferrite; (b) The weight percent of proeutectoid cementite; (c) The weight percent of pearlite; (d) The weight percent of eutectoid ferrite; (e) The weight percent of eutectoid cementite.

7. Use Figure 9.23. (a) On the diagram sketch and label by number the following heat treating processes.  (b) Prepare a table showing the process number, the product of each process, the type of quench (direct, interrupted, etc.), and common name of the process if applicable.

(1) Heat 1 hour at 860oC; water quench.

(2) Heat 1 hour at 860oC; quench in molten salt bath at 700oC; hold at 700oC for 2 hours; air cool.

(3) Heat 1 hour at 860oC; quench in molten salt bath at 350oC; hold at 350oC for 1 hour; air cool.

(4) Heat 1 hour at 860oC; quench in molten salt bath at 250oC; hold at 250oC for 1 minute; air cool.

Reference no: EM13866858

Questions Cloud

Installation of super conductor : Search the web for status of and report on an installation of "Super Conductor" Cable, 2-3 pages.
Compare and contrast three nursing advocates : Compare and contrast three nursing advocates that have brought about change to public policy. What changes need to be made in the future to be successful as a profession of nursing advocates for healthcare policy reform
Who is investigating the case and what are her credentials? : Who is investigating the case and what are her credentials?
Understand the lifetimes of the gravettians : How does the parietal and moblie art help us to understand the lifetimes of the Gravettians? What materials in their environment did they utilize? Do the works of art symbolize how they saw the world
Phase analysis and microstructure sketch : 1. Perform a phase analysis and microstructure sketch for a 1035 plain carbon steel at (a) 723+oC, and (b) 723-oC. Show the lever rule calculation for one phase at each temperature.
Determine ip address of the computer that was compromised : You've been asked to review the PCAP file and determine the IP address of the computer that was compromised, in addition to all possibly malicious IP addresses to which the system connected after the infection.
Traverse survey of the points indicated : Using a total station, carry out a traverse survey of the points indicated, apply corrections and compute co-ordinates of the stations. Describe the steps undertaken to complete.
Review - korean culture : In 200-300 words you must reply to both of the classmates post below. Be sure to label each reply so that I know which one you are addressing. Please note that "I like what you said," "That's a good point," and "I disagree with your point" do not ..
Give at least two examples of an ics : Give at least two examples of an ICS (inhaled corticosteroid) and "low dose" dosing based on the most recent NHLBI asthma guidelines. please make sure to use EBP references that are of the past 5 years and use the NHLBI guidelines to give at least tw..

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Generate the ideal current-voltage characteristics of diode

Use PSPICE to generate the ideal current-voltage characteristics of a diode from a reverse-bias voltage of 5 V to a forward-bias current of 1 mA, for an IS parameter value of (a) 10 15 A and (b) 10 13 A. Use the default values for all other parame..

  What will the output voltage be for a strain of 1000

A resistor on a Wheatstone bridge is replaced with a strain gage which has a nominal resistance of 120 Ohms and a gage factor of 2.06. The remaining resistors on this quarter-bridge Wheatstone bridge circuit are 120 Ohm fixed resistors.

  Determine the load voltage if the source voltage

Given a simple series circuit similar to that shown in the given image, determine the load voltage if the source voltage is VS= 1200°V, the load current is IL= 10-30°A, and the cable impedance is ZC= 0.5

  Determine the length of no 6 copper wire of temperature

No. 6 AWG copper wire has an area of 13.30mm2 and the resistivity at 200C is 1.75 x10-6 ohm-cm. Determine the length of No. 6 copper wireof the same temperature to give a resistance of 0.12 ohm.

  Find the coordinates of the particle at a time t later

A charged particle starts from rest at the origin of coordinates in a region where there is a uniform electric field E parallel to the x-axis, and a uniform magnetic flux density B parallel to the z-axis. Show that the coordinates of the particle ..

  What is the rotor pole shift in electrical degrees

a) If the excitation voltage E0 is equal to the terminla voltage ( 4kV ), what is the maximum real power which the motor can deliver without losing synchronism  b) What is the rotor pole shift in electrical degrees, corresponding to the nominal loa..

  Determine the full load current of single phase motor

A 50HP single phase motor operates from a 480V, 60HZ supply. When delivering full rated power the motor efficiency is 89% and the power factor is 0.78 lagging. Determine the full load current.(Hint: 746W=1HP)

  What is the rate at which the entropy of the low-temperature

What is the rate at which the entropy of the low-temperature reservoir is changing. What is the rate at which the work production is changing the entropy of the engine surroundings

  About power supply that cnanges ac to dc voltage and which

about power supply that cnanges ac to dc voltage and which a zener diode on it jst need most the calculations of

  How tall must the antennas be if the link operates on a

how tall must the antennas be if the link operates on a frequency of 1450mhz d17miles d211miles and the obstruction is

  Find an approximate expression for the response y

Consider the causal LTI system with system function H(s)=Y(s)/X(s)=1/(s+2)^2 If the input is x(t)=sin(2t) for t>0, find an approximate expression for the response y(t) that is valid for large t.

  Calculate the circuit board temperature for each case

You also do not need to consider radiation heat transger in the calculations. However, you should consider how the resuts for the no-fin cases might change if radiation heat transfer is included in the analysis Calculate the circuit board temperat..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd